Boeing 737 Type Rating Cost: Who Pays, FAA Part 142 Course Drivers, and Other Jet Ratings
Short answer: Under 14 CFR 61.63(d)(6), pilot employees of a Part 121 air carrier or Part 135 operator qualify for an aircraft type rating through their certificate holder's FAA-approved training program rather than buying a standalone retail course. If you self-fund a Boeing 737 type rating (designated B-737 by the FAA Boeing 737 Flight Standardization Board Report) at a certificated Part 142 training center, your total outlay depends on paired versus solo simulator crew scheduling, prerequisite ATP Certification Training Program hours (at least 30 classroom and 10 simulator hours under 14 CFR 61.156), full flight simulator blocks, evaluator testing fees, and lodging.
Who Pays for a Boeing 737 Type Rating and What Drives Total Cost
When you budget for a Boeing 737 type rating, start with who runs the training. Under 14 CFR 61.63(d)(6), a pilot employee of a Part 121 air carrier, a Part 135 operator, or a Part 91 Subpart K fractional ownership program manager qualifies with a flight training record endorsement from the certificate holder attesting completion of its approved ground and flight training program.
Pilots who self-fund a B-737 course enroll directly at an FAA-certificated Part 142 training center or an international Approved Training Organisation (ATO) governed by the October 2026 European Union Aviation Safety Agency (EASA) Easy Access Rules for Aircrew under Regulation (EU) No 1178/2011. Written tuition quotes vary widely based on what is bundled into the core curriculum under 14 CFR 142.3 and what is billed separately.
Two operating rules in 14 CFR Part 142 explain the biggest swings between commercial quotes. Under 14 CFR 142.65(b), each crewmember seat during flight testing, flight checking, or line-operational simulation must be occupied by a qualified crewmember or another student in the same specific course. Because the instructor giving instruction may not occupy a crewmember position, training solo adds seat-support pilot fees. Under 14 CFR 142.49(c)(1), an instructor may not conduct more than 8 hours of instruction in any 24-consecutive-hour period, excluding briefings and debriefings, setting a floor on how many hotel nights you fund.
Core expense drivers to verify on any Part 142 or ATO type rating quote
| Expense Category | Governing Rule | What to Confirm in Writing | Budget Impact if Excluded |
|---|---|---|---|
| Core Ground and Simulator Tuition | 14 CFR 142.3 and 14 CFR 142.59 qualified FFS | Included hours of CBT, flight training devices, and full flight simulator blocks | Hourly simulator overage fees if you need extra sessions |
| Paired vs Solo Scheduling | 14 CFR 142.65(b) crew seat occupancy rule | Whether tuition assumes a paired classmate or includes a seat-support pilot | Solo surcharges to pay a qualified support pilot during checks |
| ATP-CTP Prerequisite | 14 CFR 61.156 multiengine ATP test rule | Whether the 30-hour academic and 10-hour FSTD course is bundled or separate | Separate multi-day tuition and lodging before taking the ATP written |
| Evaluator Practical Test | 14 CFR 142.13(b) check within 7 calendar days | Whether the Training Center Evaluator or Examiner fee is in base tuition | Separate testing fee due before checkride, plus retest fees |
| In-Aircraft Base Training | 14 CFR 142.53(b) vs Regulation (EU) No 1178/2011 | Whether all testing runs in an approved flight simulator or jet circuits apply | Actual jet takeoffs and landings add major fuel and landing fees |
| Recurrent Currency | 14 CFR Part 61 and FSB Report Section 11 | Standalone proficiency check rate if you are not flying on the line | Recurring simulator rental and evaluator fees while job hunting |
Prerequisites and the Mandatory ATP-CTP Course (14 CFR 61.156) Based on Cert Level
Before comparing standalone type rating tuition quotes, check whether you must first complete the Airline Transport Pilot Certification Training Program (ATP-CTP). Under 14 CFR 61.63(d), every applicant adding a type rating must hold or concurrently obtain an instrument rating, hold an instructor endorsement attesting to competency at the ATP certification level, and pass the practical test at the ATP certification level in actual or simulated instrument conditions.
If you are only adding a type rating to an existing pilot certificate without applying for an ATP certificate, 14 CFR 61.63(d)(5) states that no additional knowledge test is required if you already hold an airplane, rotorcraft, powered-lift, or airship rating. If you are completing a multiengine airplane type rating concurrently with an ATP certificate, you must pass the multiengine ATP knowledge test first. FAA Form 8710-1 (03/25 edition) requires attaching your original ATP-CTP graduation certificate and valid knowledge test report, or you can submit your application online through the FAA Integrated Airman Certification and Rating Application (IACRA).
Under 14 CFR 61.156, an authorized Part 121, 135, 141, or 142 provider must deliver at least 30 hours of classroom instruction and at least 10 hours in a Part 60 flight simulation training device (FSTD). By our calculation from 14 CFR 61.156, 60 percent (6 hours) of those 10 minimum FSTD hours must run in a Level C or higher full flight simulator representing a multiengine turbine airplane with a maximum takeoff weight of 40,000 pounds or greater.
- Aerodynamics and high-altitude operations: At least 8 classroom hours under 14 CFR 61.156(a)(1).
- Meteorology and weather detection: At least 2 classroom hours under 14 CFR 61.156(a)(2).
- Air carrier operations: At least 14 classroom hours covering physiology, communications, checklists, operational control, MEL/CDL, ground operations, turbine engines, transport performance, and automation under 14 CFR 61.156(a)(3).
- Leadership and CRM: At least 6 classroom hours covering professional development and safety culture under 14 CFR 61.156(a)(4).
- Full flight simulator training: At least 6 hours in a Level C or higher FFS (40,000 pounds MTOW or greater) covering stalls, upset recovery, icing, thunderstorms, and gusty crosswinds under 14 CFR 61.156(b)(1).
- Navigation and autoflight FSTD training: Remaining FSTD training in a Level 4 or higher FSTD under 14 CFR 61.156(b)(2).
Simulator Checkrides and Base Training Rules
Self-funded applicants often confuse FAA full flight simulator testing with foreign in-aircraft base-training mandates. Under 14 CFR 142.53(b) and 14 CFR 142.59(a), the FAA Administrator specifically qualifies and approves Part 142 flight simulators for all training and all testing required for an airline transport pilot certification test, an aircraft type rating test, or both. Under Appendix 1 of the FAA Boeing 737 Flight Standardization Board (FSB) Report, Level E training is conducted in a Level C or D full flight simulator or in an aircraft.
During an added aircraft type rating checkride under 14 CFR 61.63(d)(3) and (4), the applicant must pass the practical test at the airline transport pilot certification level in actual or simulated instrument conditions. Under Section 10.1 of the FSB Report, B-737 pilot certification requires a partial flap approach and landing with leading edge devices extended and trailing edge flaps less than 15, while a no-flap approach and landing demonstration is not required.
By contrast, pilots licensing outside the FAA system must check whether post-simulator aircraft circuits are billed separately. Under EASA Regulation (EU) No 1178/2011, as amended by Commission Implementing Regulation (EU) 2026/781 for flight simulation training devices, international applicants should confirm simulator capability credits and any mandatory aircraft takeoffs and landings before signing an ATO contract.
B-737 Common Designation: Classic, NG, and 737 MAX Differences
Pilots comparing B-737 course quotes often see separate tracks for the 737 Next Generation (NG) and 737 MAX. Under Section 7.1 and Section 8.1 of the FAA Boeing 737 FSB Report, one single FAA pilot type rating designation, B-737, covers all related series on Type Certificate Data Sheet A16WE. Covered groups include the original 737 (-100, -200, -200C), 737 Classic (-300, -400, -500), 737NG (-600, -700, -700C, -800, -800BCF, -800SFP, -900, -900ER, BBJ 1, BBJ 2, BBJ 3), and 737 MAX (-7, -8, -8200, -9, BBJ MAX 8).
Holding the B-737 designation does not allow moving from a 737-800 to a 737-8 without differences training. Under the Master Differences Requirements table in Appendix 2 of the FSB Report, transitioning from the 737NG to the 737 MAX requires Level E training in a Level C or D full flight simulator (or aircraft) and Level B checking. Appendix 3 and Appendix 7 mandate simulator maneuvers covering Maneuvering Characteristics Augmentation System (MCAS) activation demonstrations, the Cross-FCC Trim Monitor, and Erroneous High Angle of Attack (AOA) during takeoff. Pilots also complete systems training on Flight Control Computer updates, Elevator Jam Landing Assist, and the Landing Attitude Modifier. Additional differences modules cover the four-unit LCD MAX Display System, the two-position landing gear control lever, and LEAP-1B engines.
Across both 737NG and 737 MAX fleets, Section 9.2.2 of the FSB Report mandates electric and manual stabilizer trim, runaway stabilizer non-normal checklists, and unreliable airspeed simulator training initially and at least once every 36 months during recurrent checks. Under Section 9.8.3, moving from a 737 Classic to a 737NG with Primary Flight Display and Navigation Display requires a minimum of 12 hours in an interactive CBT, 6 programmed hours in a Level 6 flight training device, and Supervised Line Flying. Section 9.1 also cautions that trainees without prior multiengine transport turbojet, high-altitude, flight guidance, and flight management system experience may require extra training.
Other Type Rating Costs: 777, 747-400, 757, 767, Citation 525, and BE-1900
Pilots evaluating broader type rating costs often compare narrowbody B-737 courses against widebody Boeing 777 and Boeing 747 or 747-400 fleets, medium-widebody Boeing 757 and 767 jets, light corporate Citation 525 jets, and commuter Beechcraft 1900 (BE-1900) turboprops. Under 14 CFR Part 61 and Part 142, simulator bay availability, make-and-series qualification rules, and crew-seat pairing determine how resource-intensive each course is.
Under 14 CFR 61.63(d), every added aircraft type rating is tested to ATP certification standards in actual or simulated instrument conditions. Under 14 CFR 142.47(a)(5)(ii)(A) and 14 CFR 142.59(a)-(b), Part 142 training centers must staff ATP-qualified simulator instructors and maintain FAA-approved devices matched to the specific aircraft type and variation simulated.
Regulatory simulator and crew drivers across jet and turboprop type ratings
| Aircraft Group | Part 61 Testing Standard | Simulator and Crew Rule | Primary Schedule and Tuition Driver |
|---|---|---|---|
| Boeing 737 (B-737 Classic, NG, MAX) | ATP-level practical test under 14 CFR 61.63(d) | 142.59 approved FFS, paired crew under 142.65(b) | Broad simulator availability, MAX adds Appendix 7 Level E FFS tasks |
| Boeing 757 and Boeing 767 | ATP-level practical test under 14 CFR 61.63(d) | 142.59 approved FFS, paired crew under 142.65(b) | Heavy transport systems and specialty curricula under 142.3 lengthen blocks |
| Boeing 777 and Boeing 747 / 747-400 | ATP-level practical test under 14 CFR 61.63(d) | 142.59 approved FFS, Part 121 or Part 142 curricula | Fewer non-airline retail FFS bays and longer widebody ground syllabi |
| Citation 525 Series (single-pilot or crew) | ATP-level practical test under 14 CFR 61.63(d) | 142.59 approved FFS or aircraft check under 61.63 | Trained in FFS or owner aircraft, single-pilot vs crew changes pairing |
| Beechcraft 1900 (BE-1900 turboprop) | ATP-level practical test under 14 CFR 61.63(d) | 142.59 approved FFS, paired crew under 142.65(b) | Limited active turboprop simulator locations increase travel expenses |
Six-Step Checklist Before Signing a Course Contract or Training Bond
Never pay a deposit on headline tuition alone. Under 14 CFR 142.31(a), a certificated training center may not advertise or conduct training, testing, or checking to satisfy FAA rules unless approved by the Administrator, and under 14 CFR 142.13(b), it must maintain enough approved evaluators to test graduates within 7 calendar days of course completion.
Use this six-step checklist written by our team before signing an enrollment agreement or employer training bond.
- Step 1, Prioritize employer-paid pathways first: If you are targeting a U.S. Part 121 airline, put your budget toward ATP flight-time minimums and interview preparation rather than buying a standalone course your carrier will repeat under its own Part 121 program.
- Step 2, Verify Part 142 training specifications: Request the FAA-approved course title and simulator qualification level under 14 CFR 142.11(d)(2), and confirm whether a B-737 syllabus covers 737NG only or includes 737 MAX Appendix 7 training.
- Step 3, Lock in paired-crew tuition terms in writing: Confirm whether your quote guarantees a paired classmate under 14 CFR 142.65(b) or bills you extra for a seat-support pilot if a partner cancels.
- Step 4, Itemize testing, retrain, and 7-day checkride rules: Get written rates for the evaluator fee, hourly retraining simulator time after any unsatisfactory check recorded under 14 CFR 142.73(a)(7), and checkride scheduling within the 7-calendar-day limit in 14 CFR 142.13(b).
- Step 5, Confirm certificate level and IACRA paperwork early: Review your logbook and FAA Form 8710-1 or IACRA profile with the training center ahead of Day 1, and verify your instrument rating and endorsement requirements under 14 CFR 61.63(d).
- Step 6, Audit repayment triggers in employer training bonds: For international or charter training bonds, verify the prorated forgiveness timeline, whether debt cancels if the operator furloughs crews or ceases operations, and whether hotels or recurrent checks are added to the note.
Practice example
You completed your ATP-CTP course on your own, so why did you decide against paying out of pocket for a standalone 737 type rating before applying here, and how do you know you are ready for the pace of jet simulator training?
Example answer, written by us. It is not a real applicant's story. When I finished my ATP-CTP classroom and Level D full flight simulator hours and passed my multiengine ATP written, I looked closely at how Part 142 standalone type ratings compare with an air carrier's own approved training program. A generic core curriculum teaches certification maneuvers, whereas every airline teaches its own standard operating procedures, callouts, and automation flows from day one. Putting my savings into flying consistent multiengine instrument approaches, finishing my ATP-CTP early, and staying debt-free meant I could enter ground school focused entirely on your company procedures without unlearning generic habits from another training center. During my ATP-CTP simulator sessions, my partner and I chair-flew every profile the night before so our cockpit flows and flight management entries stayed ahead of the airplane during high-altitude stall and upset scenarios. That preparation habit is what I am bringing to initial training.
This answer shows sound financial and regulatory judgment by distinguishing a generic Part 142 core curriculum from an air carrier's SOP-driven program under 14 CFR Part 121. It also backs up training readiness with a concrete habit from the candidate's ATP-CTP Level D simulator sessions.
Practice this on Fourstripe. Pick your airline and a captain runs the interview out loud: TMAAT, about-you, technical and scenario questions, with real follow-ups. You get a scored report on every answer. 7-day trial, then from $149 a week. Start a practice interview
Frequently asked questions
Do U.S. airlines make pilots pay for a Boeing 737 type rating?
Part 121 air carriers train pilot employees under their own FAA-approved programs, qualifying them via carrier flight training record endorsements under 14 CFR 61.63(d)(6). Career-track U.S. airline pilots complete type training through their carrier rather than buying a retail Part 142 course beforehand.
Does one B-737 type rating cover the 737 Classic, 737 NG, and 737 MAX?
Yes. Under the FAA Boeing 737 Flight Standardization Board Report, the single B-737 designation covers the original 737, 737 Classic, 737NG, and 737 MAX series, though moving from the 737NG to the 737 MAX requires Level E full flight simulator differences and Appendix 7 special training.
Is the ATP-CTP course included in a 737 type rating course?
They are separate FAA-approved curricula unless a school explicitly bundles them. Under 14 CFR 61.156, the ATP-CTP requires at least 30 classroom hours and 10 FSTD hours to qualify for the multiengine ATP knowledge test, whereas a type rating course covers aircraft-specific systems and ATP practical test maneuvers.
Do I have to rent a real Boeing 737 for base training to get an FAA type rating?
No. Under 14 CFR 142.53(b) and 14 CFR 142.59(a), the FAA approves qualified Part 142 full flight simulators for all training and all testing required for an aircraft type rating or ATP certification test, and the FAA Boeing 737 Flight Standardization Board Report permits Level E training in a Level C or D full flight simulator.
Does adding a Boeing 737 type rating require an FAA written exam or checkride?
Under 14 CFR 61.63(d)(5), adding a type rating requires no extra knowledge test if you already hold an airplane, rotorcraft, powered-lift, or airship rating, unless you are applying concurrently for a multiengine ATP certificate under 14 CFR 61.156. Under 14 CFR 61.63(d)(3) and (4), you must still pass the practical test at the airline transport pilot certification level in actual or simulated instrument conditions.
Sources
- 14 CFR 61.63 Additional Aircraft Ratings
- 14 CFR 61.156 Training Requirements: Multiengine ATP Certification Training Program
- 14 CFR Part 142 Training Centers
- FAA Boeing 737 Flight Standardization Board Report (Draft Revision 21)
- FAA Boeing 737 Flight Standardization Board Report (Revision 17)
- FAA Form 8710-1 Airman Certificate and/or Rating Application (03/25)
- FAA Integrated Airman Certification and Rating Application (IACRA)
- EASA Easy Access Rules for Aircrew (Regulation (EU) No 1178/2011)