Commuter Airlines: Part 135 Operations, Fleet Limits, and Pilot Requirements
Short answer: In the United States, a commuter airline flies scheduled passenger routes of at least 5 round trips per week under two distinct federal rules. For safety certification under 14 CFR Part 135, the Federal Aviation Administration limits commuter airplane operations to propeller aircraft with at most 9 passenger seats and a 7,500-pound maximum payload, or any rotorcraft, with turbojets prohibited. For economic licensing under 14 CFR Part 298, the Department of Transportation defines a commuter air carrier as a scheduled operator using small aircraft originally designed for 60 seats or fewer or an 18,000-pound maximum payload.
How US Aviation Law Defines a Commuter Airline
Every scheduled US carrier needs safety authority from the Federal Aviation Administration (FAA) and economic authority from the Department of Transportation (DOT), and each agency sets its own aircraft limits.
Under FAA Part 135 certification rules, a commuter operation conducts scheduled passenger flights in airplanes configured for a maximum of 9 passenger seats (excluding pilot seats) and a maximum payload capacity of 7,500 pounds, or in any rotorcraft. Turbojet aircraft cannot be used in Part 135 commuter operations. Holding commuter authority also allows the certificate holder to fly unscheduled on-demand charters.
Under 14 CFR 298.2 and 298.3(b), the DOT classifies a commuter air carrier as an operator carrying passengers on at least 5 round trips per week on at least one route between two or more points according to published flight schedules specifying times, days of the week, and places. Rather than holding a full section 41102 certificate, a Part 298 commuter air carrier operates under a DOT economic exemption for small aircraft originally designed for 60 passenger seats or fewer or a maximum payload capacity of 18,000 pounds or less.
Before March 20, 1997, many 10-to-30-seat scheduled airliners flew under Part 135. Under 14 CFR 135.2, scheduled passenger operators flying nontransport category turboprops with 10 to 19 seats (type certificated after December 31, 1964), transport category turboprops with 20 to 30 seats, and turbojets with 1 to 30 seats had to transition to Part 121 rules.
Commuter vs. On-Demand vs. Part 121 Scheduled Airlines
Separating Part 135 on-demand charter, Part 135 commuter service, and Part 121 scheduled airlines prevents costly regulatory mix-ups. Even an on-demand operator can fly published schedules in non-turbojet airplanes of 9 passenger seats or fewer if it stays below 5 round trips per week on each route.
Within Part 135, the FAA issues four certificate scopes through Operations Specifications (OpSpecs): Single Pilot (1 named pilot on OpSpec A040), Single Pilot in Command (1 PIC and up to 3 named SIC pilots on OpSpec A039 in aircraft of 9 passenger seats or fewer), 135 Basic (at most 5 pilots, 5 aircraft, and 3 aircraft types, capped at 9 passenger seats), and Standard Part 135, which has no preset fleet or pilot limit and requires a Director of Operations, Chief Pilot, and Director of Maintenance.
Federal operating and licensing boundaries from 14 CFR Parts 135 and 298 and FAA certification guidance
| Rule Feature | FAA Part 135 On-Demand | FAA Part 135 Commuter | FAA Part 121 Scheduled Carrier |
|---|---|---|---|
| Published schedule frequency | Fewer than 5 round trips per week on any route | 5 or more round trips per week on at least one route | Unlimited scheduled domestic or flag flights |
| Airplane passenger seat limit | 30 seats or fewer (9 seats or fewer if scheduled) | 9 passenger seats or fewer | 10 or more seats for turboprops, all scheduled turbojets |
| Airplane payload limit | 7,500 pounds maximum payload | 7,500 pounds maximum payload | Governed by Part 25 transport category limits |
| Turbojet airplanes permitted | Yes for unscheduled flights, no for scheduled | No turbojet aircraft allowed | Yes |
| Rotorcraft permitted | Any rotorcraft | Any rotorcraft | Not applicable to airplane Part 121 rules |
| Pilot qualification and hour rules | Commercial certificate, or ATP for turbojets and 10-or-more-seat airplanes (1,500 hours PIC and 500 hours SIC for eligible on-demand) | ATP certificate for multiengine airplane or powered-lift PIC, plus 100 hours PIC in make and model for single-pilot autopilot | Part 121 Subparts N and O training and 14 CFR 121.436 pilot qualification rules |
| DOT economic authorization | Air Taxi Registration (OST Form 4507) | Commuter Air Carrier Authorization | Commuter Authorization (at most 60 seats) or Section 41102 Certificate |
Worked Example: How Frequency and Seats Shift Certification
To see how FAA safety rules and DOT economic licensing interact, walk through three stages of a hypothetical operator launching scheduled passenger flights between a rural town and a hub airport. This worked example is written by our team using 14 CFR Parts 135 and 298.
Stage 1: Four weekly round trips in a 9-seat turboprop. Publishing 4 round trips per week in a turboprop with 9 passenger seats and under 7,500 pounds of payload stays below the 5-round-trip threshold. The carrier can fly under FAA Part 135 On-Demand authority and file OST Form 4507 with the DOT as an Air Taxi Operator at least 30 days before starting operations.
Stage 2: Adding a fifth weekly round trip in the same 9-seat airplane. Reaching 5 published round trips per week triggers commuter licensing under 14 CFR 298.21 footnote 7 and 298.50. Compared with Air Taxi Operator registration, applying for a DOT Commuter Air Carrier Authorization requires a full fitness review and a $670 filing fee (ecfr.gov, as of November 2026), alongside FAA Part 135 Commuter operations specifications. Under 14 CFR 298.52, active commuter authority also covers on-demand charters, scheduled cargo, contracted US Postal Service mail, air ambulance, and firefighting flights.
Stage 3: Up-gauging to a 19-seat turboprop or 30-seat jet. Under 14 CFR 135.2, neither aircraft can fly scheduled passenger service under Part 135, so the operator must earn FAA Part 121 operations specifications. Because both airplanes were originally designed for 60 seats or fewer and at most 18,000 pounds of payload, the carrier still operates small aircraft under 14 CFR 298.2 and can keep its DOT Commuter Air Carrier economic authority.
Pilot Qualifications, Operating Experience, and Crew Rules
While some Part 135 VFR jobs require only a Commercial Pilot Certificate and eligible two-pilot on-demand operations under 14 CFR 135.4 set minimums at 1,500 hours total time for the PIC and 500 hours for the SIC, scheduled multiengine commuter flying carries stricter federal PIC rules.
Under 14 CFR Part 135, you cannot serve as pilot in command of a multiengine airplane in a commuter operation unless you hold an Airline Transport Pilot (ATP) certificate with appropriate category and class ratings and, if required, an appropriate type rating. The same ATP rule applies to any turbojet airplane, any airplane with 10 or more passenger seats, and any commuter powered-lift (with a type rating not limited to VFR).
In smaller aircraft, to serve as PIC without a Second in Command in a commuter operation using an operative approved autopilot system authorized by operations specifications, Part 135 requires at least 100 hours of PIC flight time in the exact make and model of aircraft to be flown. Before designation as a commuter PIC, you must also complete initial operating experience in that make and basic model during actual Part 135 commuter passenger-carrying flights.
When a commuter operator flies airplanes requiring two pilots under type certification rules, 14 CFR 135.3(b) requires Part 121 Subparts N and O pilot training and qualification (though SICs may meet 14 CFR 135.245 instead of 121.436). Carriers must also review the last 5 years of pilot records under the Pilot Records Improvement Act (PRIA) and enroll pilots in a 14 CFR Part 120 drug and alcohol testing program.
Rural Routes, Interline Tickets, and Passenger Experience
Under 49 U.S.C. 41738 and 14 CFR 298.32, rural communities designated as eligible places cannot receive scheduled passenger commuter service unless the DOT first finds the carrier fit, willing, and able and issues a Commuter Air Carrier Authorization. Active operators appear on the DOT Office of Aviation Analysis Commuter Air Carrier List, last updated May 8, 2026.
Even with 9-seat aircraft, commuter tickets connect directly onto major network airlines. Under 14 CFR 298.3(b) and 298.11, commuter air carriers keeping a signed counterpart of Agreement 18900 (OST Form 4523) on file can maintain interline baggage and ticketing agreements and joint tariffs with certificated domestic or foreign airlines. Under 14 CFR 298.30, staffed counters must display baggage liability and denied boarding compensation signs, and any ticket with a segment on a large aircraft (more than 60 seats) requires a written baggage liability notice.
Federal safety rules shape what passengers experience aboard a 9-seat commuter flight:
- Weight, balance, and obstacle clearance: Multiengine manuals must enforce weight and balance procedures under 14 CFR 135.23(b). Commuter category airplanes under 14 CFR 135.398 must take off at weights clearing all obstacles by at least 35 feet vertically, or at least 200 feet horizontally inside airport boundaries and 300 feet outside.
- Part 135 exit-seating restrictions also exempt commuter operations with 9 or fewer passenger seats, and pilots deliver preflight safety briefings under 14 CFR 135.117.
- Terminals and hazmat screening: Under 49 CFR 1544.101, whether a Part 135 flight boards through a sterile TSA concourse or an alternate facility depends on operation type, maximum certificated takeoff weight, seating capacity, and sterile-area access. Every Part 135 carrier must also maintain an FAA-approved Hazardous Materials Training Program under Subpart K.
DOT Fitness and FAA Part 135 Certification
Beginning September 30, 2026, the FAA transitioned initial Part 135 air carrier and operator certificate applications to Aviation Integrated Safety Services (AIS Services) under Notice 8900.766. The portal supports digital uploads up to 500MB per file across five certification phases. Under 14 CFR 135.25, a certificate holder must maintain exclusive use of at least one conforming aircraft through ownership or a written lease of at least 6 consecutive months. Aircraft type certificated for 9 passenger seats or fewer may be maintained under Parts 91 and 43 using annual, 100-hour, or Approved Aircraft Inspection Programs. Aircraft with 10 or more seats require a Continuous Airworthiness Maintenance Program (CAMP) and a separate General Maintenance Manual.
The DOT Air Carrier Fitness Division applies a three-part fitness test under 14 CFR 204.3. It reviews managerial competence, verified start-up capital with 3-year historical and first-year forecast financials, and a 10-year compliance record. Carriers must also file OST Form 6410 liability insurance under Part 205. Under 49 U.S.C. 40102(a)(15), a corporate US carrier needs a US citizen president and at least two-thirds US citizens on its board and managing officers. US citizens must also hold actual control and at least 75 percent of the voting interest. Active commuters file a first-year progress report within 45 days after year one, quarterly BTS Form 298-C financial reports, and monthly Schedule T-100 traffic data within 30 days. Carriers face dormancy termination after 1 year without operations.
Commuter Operations in Canada (CARs Subpart 704)
Transport Canada uses a wider aircraft bracket for commuter airlines under Part VII of the Canadian Aviation Regulations (CARs). It divides operators into Subpart 703 (Air Taxi), Subpart 704 and Commercial Air Services Standard 724 (Commuter Operations, amended August 13, 2026), and Subpart 705 (Airline Operations). Under Standard 724.15, Type C operational control covers IFR and night VFR commuter operations in airplanes with 10 to 19 passenger seats or turbojets with 19 or fewer passenger seats. Day VFR non-turbojet commuter flights use Type D operational control. Both systems delegate pilot self-dispatch to the PIC backed by company flight following. Type A or B co-authority dispatch is required only for No Alternate IFR flights.
Under Standard 724.07, an IFR commuter Chief Pilot must hold an Airline Transport Pilot License (Airplane), an Instrument Rating, and at least 3 years of commuter airplane PIC experience. Under Standard 724.26, reduced-visibility takeoffs down to RVR 1,200 feet (1/4 mile) or RVR 600 feet require at least 100 hours of PIC time on type. The airplane needs dual attitude indicators marked to at least 15 degrees of pitch with an operative failure warning system. Crews must also file a takeoff alternate within 60 minutes for twin-engine airplanes or 120 minutes for airplanes with three or more engines.
How to Prepare for a Commuter Airline Pilot Interview
Interviewing at a Part 135 commuter carrier tests airline-grade instrument discipline alongside small-aircraft ownership. On a 9-seat route with no flight attendant in the cabin, interview panels want to hear your own real flying stories showing sound PIC judgment. Use this six-step preparation checklist written by our team:
- Verify your certificates and make-and-model hours: Confirm whether the role flies multiengine scheduled commuter routes (requiring an ATP certificate under Part 135) or single-pilot autopilot IFR (requiring 100 hours of PIC time in that exact make and model).
- Check your 5-year PRIA paper trail: Make sure your logbooks, checkride dates, and past employer records align cleanly for the mandatory 5-year PRIA review.
- Review Part 135 IFR and performance rules: Be ready to explain alternate minimums, Minimum Equipment List (MEL) deferrals at outstations, and 14 CFR 135.398 obstacle clearance margins.
- Prepare a real weight-and-balance story: Practice walking through a flight where extra alternate fuel forced baggage or seat adjustments inside a 7,500-pound payload cap.
- Show calm passenger communication: Pick an example where you delivered a safety briefing under 14 CFR 135.117 or explained a weather delay face-to-face on the ramp.
- Practice out loud in plain first-person detail: State the aircraft, weather or weight constraint, guiding rule, passenger communication, and outcome without rehearsed scripts.
Moving From Part 135 Commuter Flying to Part 121 Airlines
Scheduled Part 135 commuter flying builds habits that translate directly to Part 121 airline interviews: flying published timetables across all seasons, working inside a General Operations Manual and Standard Operating Procedures, applying MEL procedures, and making conservative PIC go-or-no-go calls.
Practice example
Tell me about a time on a short-haul or single-pilot flight when changing weather or weight-and-balance limits forced you to delay or modify a departure while passengers were waiting.
Example answer written by our team. The applicant is invented. Last winter I was flying a nine-seat piston twin on an afternoon leg when freezing rain moved over our destination faster than forecast, dropping ceiling and visibility near minimums and requiring an alternate further south. Adding the extra alternate fuel pushed our ramp weight over maximum takeoff weight with seven passengers and their winter bags aboard. With passengers already standing inside the FBO lounge, I paused boarding, recalculated our weight and balance using actual bag weights from the scale, and coordinated with operations to hold two heavy checked ski bags for the evening flight. Before walking out to the ramp, I explained the weather change and fuel requirement plainly to the two affected passengers so they knew why their gear was following later. Everyone boarded calm, we departed within legal takeoff weight and center-of-gravity limits, and we landed safely with full reserve fuel. That flight reinforced that schedule pressure on quick turnarounds can never rush a weight calculation.
Commuter pilots work face-to-face with passengers without a flight attendant or gate agent buffer, so interviewers look for calm communication alongside strict compliance with weight-and-balance rules. This answer walks through the specific weather trigger, the exact fuel-versus-payload tradeoff, how the pilot briefed passengers directly, and the safe outcome.
Practice this on Fourstripe. Pick your airline and a captain runs the interview out loud: TMAAT, about-you, technical and scenario questions, with real follow-ups. You get a scored report on every answer. 7-day trial, then from $149 a week. Start a practice interview
Frequently asked questions
What is the difference between a commuter airline and a regional airline?
Under FAA Part 135 safety rules, a commuter airline flies scheduled passenger routes in propeller airplanes configured for 9 passenger seats or fewer and a 7,500-pound maximum payload, or in rotorcraft, with turbojets prohibited. Under 14 CFR 135.2, scheduled passenger airlines flying turboprops with 10 or more seats or any turbojet must operate under FAA Part 121, like regional jet and mainline carriers.
How many flights per week make an airline a commuter carrier?
Under 14 CFR 298.2 and FAA Part 135 rules, commuter status begins at 5 or more round trips per week on at least one route between two or more points according to published flight schedules. A Part 135 on-demand operator may fly fewer than 5 scheduled round trips per week on a route using non-turbojet airplanes with 9 passenger seats or fewer.
Do commuter airline pilots need an ATP certificate?
Under 14 CFR Part 135, any pilot in command of a multiengine airplane or a powered-lift in a scheduled commuter operation must hold an Airline Transport Pilot (ATP) certificate with the required ratings. A commuter PIC flying single-pilot with an approved autopilot instead of a second in command also needs at least 100 hours of PIC time in that make and model.
Why does the DOT allow 60 seats for commuter air carriers while the FAA limits them to 9 seats?
The DOT's 60-seat and 18,000-pound payload cap in 14 CFR Part 298 is an economic licensing exemption for small-aircraft operators, whereas the FAA's 9-seat and 7,500-pound cap sets the safety limit for Part 135 commuter airplanes.
Can commuter airlines sell connecting interline tickets with major airlines?
Yes, 14 CFR 298.3(b) and 298.11 allow commuter air carriers with Agreement 18900 (OST Form 4523) on file to maintain interline agreements, joint tariffs, and through-service tickets with certificated domestic and foreign airlines. When a ticket includes a segment on an aircraft with more than 60 seats, 14 CFR 298.30 requires a written baggage liability notice with the ticket.
Sources
- 14 CFR Part 135: Operating Requirements for Commuter and On Demand Operations (eCFR)
- 14 CFR Part 298: Exemptions for Air Taxi and Commuter Air Carrier Operations (eCFR)
- 14 CFR 204.3: Applicants for New Certificate or Commuter Air Carrier Authority (eCFR)
- FAA 14 CFR Part 135 Air Carrier and Operator Certification
- FAA General Information on Types and Scope of 14 CFR Part 135 Operations
- FAA General Requirements for 14 CFR Part 135 Certification
- US Department of Transportation: U.S. Air Carriers Licensing and Fitness
- US Department of Transportation: How to Become a Commuter Air Carrier
- US Department of Transportation: Commuter Air Carrier List
- Transport Canada: Canadian Aviation Regulations (SOR/96-433)
- Transport Canada: Standard 724 Commuter Operations