Flight Simulators for Pilot Training: Official Tiers, Logging Rules, and Home Practice Guide

Short answer: Flight simulators for pilot training split into uncertified home desktop software for procedural study and civil-aviation-qualified devices that count toward pilot certificates, ratings, and instrument currency. Under 14 CFR Part 60 and Advisory Circular 61-136B, the FAA oversees 4 Flight Training Device levels (Levels 4 through 7), 4 Full Flight Simulator levels (Levels A through D), and 2 Aviation Training Device tiers (BATD and AATD) approved on a 5-year Letter of Authorization schedule. The best flight simulator for pilot training depends on your syllabus stage, because you can only log hours flown on an approved hardware-and-software configuration with its official qualification documents on hand.

Matching flight simulators for pilot training to your syllabus stage

If you are asking whether a flight simulator is good for pilot training, the answer is yes when you match the device to the right learning task.

Searching for the best flight simulator pilot training setup brings up everything from consumer PC software to airline motion bays. Civil aviation authorities draw a strict legal line between home practice rigs and qualified pilot flight simulator training devices. A home rig helps you rehearse checklists and radio calls, while only a qualified pilot training flight simulator holding an active regulatory approval lets you credit hours toward a certificate, rating, or recency requirement.

Use this tier-selection plan written by our team to choose the right flight simulator for pilot training.

  • Pre-solo and Private Pilot study: Pair a home desktop setup with physical yoke and rudder pedals for unlogged checklist and radio rehearsal, or fly an FAA-approved Basic Aviation Training Device (BATD) with an instructor for authorized dual credit.
  • Instrument Rating and IFR currency: Train in an FAA-approved BATD or Advanced Aviation Training Device (AATD) to drill holds, ILS and RNAV approaches, unusual attitudes, and partial-panel failures before verifying proficiency in the airplane.
  • Commercial Pilot, CFI, ATP, and Instrument Proficiency Checks (IPC): Step up to an FAA-approved AATD, Part 60 Flight Training Device (FTD), or Full Flight Simulator (FFS), since BATDs are ineligible for Commercial, ATP, CFI, or IPC credit.
  • ATP-CTP, type ratings, and airline recurrent checks: Train in aircraft-specific Part 60 FTDs (Levels 4 through 7), Full Flight Simulators (Levels A through D), or European devices qualified under EASA Certification Specifications.

FAA Flight Simulator and Aviation Training Device Tiers (Sources: FAA National Simulator Program and AFS-800 guidance, 2026)

Simulator Tier Governing FAA Rule Core Hardware and Fidelity Authorized Training Scope
Home Desktop Simulator Uncertified (no FAA approval) Consumer PC, monitor or VR headset, and desktop controls Unlogged chair-flying, checklist flows, and procedural study only
Basic Aviation Training Device (BATD) 14 CFR 61.4(c) and FAA ATD Appendix B Physical flight controls, physical panel switches, VFR/IFR instruments, and 25 NM Part 97 nav database Private Pilot, Instrument Rating, and instrument recency of experience per LOA
Advanced Aviation Training Device (AATD) 14 CFR 61.4(c) and FAA ATD Appendix C Ergonomic cockpit shell, adjustable pilot seat, 2-axis autopilot/FD, and separate instructor station Private, Instrument, Commercial, ATP, CFI, instrument recency, and IPC per LOA
Flight Training Device (FTD Levels 4 to 7) 14 CFR Part 60 (National Simulator Program) Aircraft-specific fixed-base flight deck and validated systems under an active SQMS Systems integration, multi-crew flows, and Part 60 credit per Statement of Qualification
Full Flight Simulator (FFS Levels A to D) 14 CFR Part 60 (National Simulator Program) Full aircraft flight deck replica, visual system, and evaluated motion cueing Aircraft type ratings, UPRT, full stall, low-visibility taxi, and airline recurrent checks

FAA BATD vs. AATD rules and authorized training limits

Most general aviation flight schools and university programs run Basic or Advanced Aviation Training Devices evaluated by the FAA General Aviation and Commercial Division, Airmen Certification and Training Branch (AFS-810) in Washington, DC. Manufacturers submit a Qualification and Approval Guide (QAG), demonstration video, and evaluation request at least 90 days in advance of proposed training use (120 days recommended) to earn a 5-year Letter of Authorization (LOA), and may apply for renewal within 120 days of expiration. Legacy approvals for ground trainers, FTD Levels 1 through 3, and personal computer-based aviation training devices (PCATDs) lacking an expiration date or not issued by the General Aviation and Commercial Division terminated on December 31, 2015 under Federal Register Docket No. FAA-2013-0809.

A BATD covers procedural and operational tasks for the Private Pilot Certificate, Instrument Rating, and instrument recency under 14 CFR Parts 61 and 141. An AATD meets every BATD standard and adds realistic switch sizing and reach from an adjustable fixed pilot seat, a two-axis autopilot and flight director where standard, day and night VFR and IFR airport visual cues, automated ATC or scenario-based training options, and an independent instructor station. Those upgrades add Commercial Pilot, ATP, Flight Instructor, and IPC eligibility.

Under Part 61, instructors and students may use an approved ATD directly per its LOA without extra local FAA sign-off. Under Part 141, a pilot school must notify its Principal Operations Inspector (POI) and obtain Flight Standards District Office (FSDO) authorization in its Training Course Outline (TCO). Combined BATD, AATD, FTD, and FFS hours toward an Instrument Rating cannot exceed the cap in 14 CFR 61.65 or the 50 percent maximum of required training under 14 CFR Part 141 Appendix C, paragraph 4(b)(4). Even on an AATD, federal rules bar using an ATD for the following milestones.

  • Practical tests and type ratings: You cannot take a checkride, complete aircraft-type-specific training, or earn an aircraft type rating in an ATD.
  • Solo, night, cross-country, and landing minimums: Certification requirements for solo, cross-country, night flight, or takeoffs and landings cannot be completed in an ATD.
  • Airplane-specific hours: Hours explicitly assigned to an aircraft must be flown in that aircraft, including the 3 hours of instrument maneuvering in a single-engine airplane for a Private Pilot Certificate under 14 CFR 61.109(a)(3).
  • IPC vs. recency: Both BATDs and AATDs can be authorized for 14 CFR 61.57 instrument recency, whereas only an AATD can be authorized for portions of an IPC.

Part 60 Flight Training Devices and Full Flight Simulators

Regional, corporate, and major airline training programs use Flight Simulation Training Devices (FSTDs) qualified under 14 CFR Part 60 by the FAA National Simulator Program (NSP) Branch (updated June 8, 2026), including FTDs at Levels 4 through 7 and Full Flight Simulators (FFSs) at Levels A through D. Every Part 60 sponsor must run a Simulation Quality Management System (SQMS) and hold a Part 60 Statement of Qualification.

FAA qualification guidance (updated May 29, 2026) includes the AC 120-40 series (through Draft AC 120-40C) for airplane simulator qualification, AC 120-50A for windshear training programs, and the AC 121-14 series for simulator and visual evaluation. Separately, the FAA Airmen Training and Certification Group (updated August 18, 2026) collaborates on Airline Transport Pilot Certification Training Program (ATP-CTP) policy and approvals under 14 CFR Part 141. To support high-risk jet training, the NSP issues enforceable FSTD Directives and technical Information Bulletins.

  • Extended Reality (XR) qualification: NSP FSTD Information Bulletin 26-01 (revised June 5, 2026) guides Part 60 qualification for simulators using Extended Reality systems.
  • High-risk envelopes: FSTD Directive 2 (effective May 31, 2016) and related bulletins govern full stall training, Upset Prevention and Recovery Training (UPRT), airframe and engine icing, gusting crosswinds, Objective Motion Cueing Tests, and bounced landing recovery.
  • Low-visibility and vision systems: FSTD Directive 1 (effective May 30, 2010) and NSP bulletins cover Class II and Class III airport visual models, Runway Status Lights (RWSL), Land and Hold Short Operations (LAHSO), SMGCS, Head-Up Displays (HUD), Enhanced Flight Vision Systems (EFVS), Night Vision Goggles (NVG), and RNP/AR.

European EASA and UK CAA simulator rules from 2026 to 2028

In Europe, EASA historically grouped simulators into fixed tiers such as FNPT and FFS under CS-FSTD(A) Issue 2 (published May 3, 2018) for aeroplanes and CS-FSTD(H) (published July 4, 2012) for helicopters. On July 15, 2026, EASA published CS-FSTD Issue 1 (ED Decision 2026/008/R) and Regulation (EU) 2026/781, replacing fixed categories with the capability-based FSTD Capability Signature (FCS).

The FCS describes a simulator's actual features and fidelity levels, making EASA the first aviation authority worldwide to implement elements of ICAO Doc 9625. The framework adds an optional task-to-tool methodology for type ratings and recurrent checks, plus qualification rules for touchscreen flight decks and Extended Reality (XR), building on earlier EASA Special Conditions for Virtual Reality Head Mounted Displays (HMDs) paired with reduced-stroke motion on helicopter FNPT Level II and FTD Level 3 devices. Regulation (EU) 2026/781 and CS-FSTD Issue 1 become applicable on April 30, 2028, supported by Implementation Support Task IST.0007 (starting with a December 15, 2026 session in Cologne, a Q1 2027 manual, and 2027 workshops).

Before paying for European or UK simulator time, verify the device online. EASA's portal splits approvals into EASA FSTD IS and NAA FSTD IS (devices qualified by EU Member State and EFTA National Aviation Authorities). In the United Kingdom, the UK CAA ratifies Part-ORA compliance via an operator Qualification Certificate and publishes UK Qualified FSTD Datasheets. Under two US-EU Bilateral Aviation Safety Agreement (BASA) Annexes signed November 19, 2020, plus active FAA BASA Simulator Implementation Procedures with Canada, the UK, and the EU, authorities also accept reciprocal recurrent FFS evaluations.

Official Simulator Oversight and Verification Portals Across the US, EU, and UK (Sources: FAA, EASA, and UK CAA, 2026)

Regulator Primary Qualification Rules Operator Approval Document Public Verification Method
FAA (General Aviation) 14 CFR 61.4(c), Parts 61/141, and AFS-800 ATD guidance 5-year Letter of Authorization (LOA) and approved QAG FAA Approved ATD list and physical or electronic LOA at the trainer
FAA (Part 60 Airline/FTD) 14 CFR Part 60 and SQMS guidelines Part 60 Statement of Qualification (SOQ) FAA NSP Qualified Flight Simulation Training Devices list
EASA (EU and EFTA States) CS-FSTD(A)/CS-FSTD(H), moving to Reg (EU) 2026/781 on April 30, 2028 FSTD Qualification Certificate (with FCS from April 2028) EASA FSTD IS and NAA FSTD IS online registries
UK CAA UK Part-ORA technical and organizational criteria UK CAA Qualification Certificate issued to the operator UK Qualified FSTD Datasheets and UK CAA online FSTD search tool

Microsoft Flight Simulator and home setups vs. certified trainers

Many students ask whether Microsoft Flight Simulator for pilot training is worth using, or whether consumer flight simulator pilot training builds bad habits. Used carefully, Microsoft Flight Simulator and similar desktop programs are practical study aids for learning panel layouts, briefing approach plates, and rehearsing emergency memory items before dual flight lessons.

Standalone consumer software on a home PC never yields loggable hours. Under FAA ATD design criteria, an approved trainer cannot use a keyboard, mouse, or gaming joystick for simulated flight control, and after initial scenario setup you cannot use a mouse or key to position landing gear, wing flaps, cowl flaps, carburetor heat, mixture, propeller, or throttle controls. Even when an ATD maker licenses commercial software, FAA approval covers only the exact unified hardware-and-software package in the QAG, and no outside software may run after the startup self-test.

FAA guidance also notes that even approved ATDs have no requirement for control loading to replicate a specific aircraft. Follow these four rules at home to avoid negative transfer of training.

  • Treat pitch and trim as procedural: Spring or bungee desktop yokes lack aerodynamic airflow loads, so practice power-plus-attitude workflows at home and learn trim pressures in the airplane.
  • Keep your eyes outside on VFR patterns: Desktop screens tempt students to fixate on airspeed and vertical speed tapes instead of flying visual sight pictures.
  • Never hit pause or reset mid-approach: Restarting after a localizer deviation ruins error management. Fly the correction or execute the published missed approach.
  • Use physical switches and knobs: Mouse-clicking virtual dials builds zero muscle memory for turbulent IMC when your hand must locate physical radio, flap, and trim controls.

Hardware, display, and failure standards inside an approved ATD

Swapping physical panels or avionics on an FAA-approved ATD without submitting a revised QAG for evaluation can terminate its approval. Airplane ATDs must feature a self-centering yoke or stick, self-centering rudder pedals, continuous throttle, propeller, and mixture/condition levers, plus physical controls for flaps, pitch trim, radios, clock/timer, gear handle, transponder, altimeter, carburetor heat, and cowl flaps. Helicopter ATDs require a cyclic, collective, throttle/rpm control, antitorque pedals, and applicable panel controls. Both require physical switches for master/battery, magnetos, alternators/generators, APU (if applicable), fuel boost pumps, avionics master, pitot heat, and exterior lights. Touchscreens on an AATD may replicate push-buttons, while physical knobs, levers, or handles are mandatory for twisting or pulling actions.

Displays must run an automatic startup self-test verifying zero transport delay and provide 14 CFR 91.205 day VFR and IFR equipment: an altimeter marked every 20 feet or less, magnetic direction indicator, 360-degree heading indicator marked every 5 degrees or less, airspeed indicator (markings under 20 knots optional), VSI marked every 100 fpm to 1,000 fpm and every 500 fpm to at least plus or minus 2,000 fpm, 3-degree-per-second turn-rate indicator, and inclinometer. Every ATD also requires a 25 NM Part 97 local navigation database, horizontal and vertical track recording, and QAG performance tables for sea level and 5,000 feet MSL (or 6,000 feet if published, and 18,000 feet for turboprop or turbojet models).

During dual instruction, instructors can trigger 6 failure categories without freezing the simulation: alternator/generator, vacuum/pressure pump, gyroscopic instruments, pitot-static, electronic flight displays, and landing gear or flaps. On an AATD, the separate instructor station must also plot airways, holds, NAVAIDs, airports, altitude, speed, and full ground-track history.

How to verify an LOA and log simulator time on FAA Form 8710-1

Logging simulator sessions in aircraft columns is a frequent checkride logbook error. FAA evaluators and Designated Pilot Examiners (DPEs) are instructed to request a copy of the manufacturer's LOA whenever an applicant credits ATD hours toward certificate or rating minimums. Run this 5-step checklist written by our team before and after every approved ATD lesson.

  • Step 1, Check the 3 required station documents: Confirm the unexpired 5-year FAA LOA, matching QAG, and aircraft performance tables are accessible at the trainer (electronic copies are allowed).
  • Step 2, Watch the startup self-test: Verify normal control input and transport delay confirmation at startup, and stop logging immediately if any uncommanded visual or control malfunction occurs.
  • Step 3, Leave all Flight Time columns blank: Never enter ATD time under Total Flight Time, Airplane Single-Engine Land, Multiengine Land, PIC, Night, or Cross-Country.
  • Step 4, Count only configured IMC minutes: Log simulated instrument time only while the visuals are set to IMC and you fly solely by reference to instruments.
  • Step 5, Record the LOA model and save the LOA: Per 14 CFR 61.51(b)(1)(iv), write the exact ATD type and identification from the LOA, carry credit only into BATD/AATD, Instruction Received (Dual), Instrument Time, or Total Time for FAA Form 8710-1, and keep a copy of the LOA.

Worked ATD logbook example for your checkride folder

Here is a worked example written by our team for an Instrument Rating student completing a 1.5-hour dual lesson in an FAA-approved AATD. After confirming the unexpired 5-year LOA, QAG, and self-test pass with your instructor, you spend 0.2 hours in simulated day VFR setting up avionics and practicing taxi runway-incursion callouts, then 1.3 hours in configured IMC flying two ILS approaches, one RNAV approach, a hold, and a pitot-static failure recovery solely by reference to the instruments.

In your logbook, leave Total Flight Time, Airplane Single-Engine Land, PIC, Night, and Actual Instrument blank (0.0). Log 1.5 hours in your AATD column, 1.5 hours in Dual Instruction Received, and 1.3 hours in Simulated Instrument, noting the exact LOA device identification, approaches flown, and instructor endorsement. On the FAA Form 8710-1 Pilot Time grid, place those 1.5 hours in the ATD row rather than the Aircraft row so your examiner can verify your totals cleanly.

Practice example

Walk me through how you used flight simulators during your instrument training, and how you verify that simulator hours in your logbook are legal to count on FAA Form 8710-1.

Example answer, written by us. It is not a real applicant's story. During my instrument rating, my instructor and I used an FAA-approved Advanced Aviation Training Device before flying each new procedure in the airplane. We practiced holding entries, ILS and RNAV approaches, partial-panel scans, and pitot-static or vacuum failures while pausing to brief mistakes without burning fuel. Before starting any session, I verified that the current 5-year FAA Letter of Authorization, the approved Qualification and Approval Guide, and the aircraft performance tables were available at the station, and we watched the startup self-test pass with zero transport delay warnings. When logging those sessions, I left every aircraft flight time column blank in my logbook. I recorded the exact device model and identification from the Letter of Authorization, logged simulated instrument time only when the visuals were set to IMC, and carried the hours solely into dual instruction received, simulated instrument, and total time on FAA Form 8710-1.

This answer shows an interview panel that you treat ground simulation as structured preparation rather than a shortcut around flying the airplane. Naming the 5-year Letter of Authorization, the startup self-test, and the blank flight-time column rule proves your logbook will pass a checkride or airline records audit cleanly.

Practice this on Fourstripe. Pick your airline and a captain runs the interview out loud: TMAAT, about-you, technical and scenario questions, with real follow-ups. You get a scored report on every answer. 7-day trial, then from $149 a week. Start a practice interview

Frequently asked questions

Can I log Microsoft Flight Simulator or home desktop simulator hours in my pilot logbook?

No, standalone consumer flight simulator software on a home PC cannot be logged toward pilot certificates, ratings, or currency. Under FAA Advisory Circular 61-136B, loggable time requires an FAA-evaluated hardware-and-software package with physical aircraft controls, plus an active 5-year Letter of Authorization and Qualification and Approval Guide at the station.

What is the difference between an FAA BATD and an AATD?

A Basic Aviation Training Device (BATD) covers procedural and operational training for the Private Pilot Certificate, Instrument Rating, and instrument recency of experience. An Advanced Aviation Training Device (AATD) adds realistic cockpit ergonomics, an adjustable pilot seat, a two-axis autopilot and flight director where standard, and an independent instructor station, adding Commercial Pilot, ATP, Flight Instructor, and IPC eligibility.

Do flight simulator hours count as flight time on FAA Form 8710-1?

No. All logbook columns referencing aircraft flight time must remain blank when logging ATD sessions, and hours may only be credited as BATD or AATD time, Instruction Received (Dual), Simulated Instrument Time (while configured in IMC), or Total Time on the FAA Form 8710-1 pilot time grid.

Can I take a pilot checkride or earn a type rating in an Aviation Training Device?

No, FAA rules prohibit using a BATD or AATD for practical tests, aircraft-type-specific training, type ratings, or solo, night, cross-country, and landing minimums. Aircraft type ratings and airline recurrent checks require higher-tier simulators such as 14 CFR Part 60 Full Flight Simulators (Levels A through D).

What is EASA's FSTD Capability Signature (FCS) and when does it take effect?

Established under Regulation (EU) 2026/781 and CS-FSTD Issue 1 (published July 15, 2026), the FSTD Capability Signature describes a simulator's actual technical features and fidelity levels rather than placing it in a fixed legacy category. The FCS framework and optional task-to-tool training methodology take effect across Europe on April 30, 2028.

Sources