Horizon Airlines Careers: FAA Part 121 Pilot Qualifications and Hiring Requirements

Short answer: Pilots preparing for Horizon Airlines careers or any U.S. airline operating under 14 CFR Part 121 must hold an Airline Transport Pilot (ATP) certificate or Restricted Privileges ATP (R-ATP) certificate and an appropriate aircraft type rating to serve as Second in Command (14 CFR 121.436). A standard unrestricted ATP certificate requires 1,500 hours of total pilot time at age 23, while R-ATP pathways allow eligible pilots at age 21 to qualify with 750, 1,000, or 1,250 hours under 14 CFR 61.160. Before starting service, you must also complete a 40-hour ATP Certification Training Program under 14 CFR 61.156, apply for FAA Pilot Records Database access at least 7 days before seeking to access the database, and provide written consent for record evaluation under 14 CFR Part 111.

FAA Qualification Rules for Part 121 Airline Pilots

When you pursue Horizon Airlines careers as a flight crewmember, your baseline eligibility is governed by federal air carrier regulations under 14 CFR Part 121 Subpart O. Every pilot acting as Second in Command (First Officer) or Pilot in Command (Captain) in Part 121 operations must meet certification, aircraft type rating, medical, and operational experience standards before flying the line.

Under 14 CFR 121.436(b), a Second in Command must hold an Airline Transport Pilot certificate (unrestricted or restricted privileges) and an appropriate aircraft type rating for the aircraft being flown. A second-in-command type rating obtained under 14 CFR 61.55 does not satisfy this requirement. In addition, 78 FR 42324 confirms that a Second in Command in standard two-pilot Part 121 operations must hold at least a second-class medical certificate, whereas flag or supplemental operations requiring three or more pilots require an unrestricted ATP certificate, an appropriate aircraft type rating, and a first-class medical certificate.

Upgrading to Pilot in Command (Captain) under 14 CFR 121.436(a) requires an unrestricted ATP certificate (not subject to 14 CFR 61.167 limitations), an appropriate aircraft type rating, a first-class medical certificate, and at least 1,000 hours of qualifying air carrier or commercial experience accumulated through any combination of:

  • Second in Command in Part 121 operations.
  • Pilot in Command in fractional ownership operations under 14 CFR 91.1053(a)(2)(i).
  • Pilot in Command in commuter or on-demand operations under 14 CFR 135.243(a)(1).
  • Pilot in Command in eligible on-demand operations requiring the pilot to satisfy 14 CFR 135.4(a)(2)(ii)(A).
  • Up to 500 hours of military flight time obtained as Pilot in Command in a multiengine, turbine-powered, fixed-wing airplane or powered-lift aircraft in an operation requiring more than one pilot (14 CFR 121.436(c)).
  • Flight time obtained as Pilot in Command in Part 121 operations prior to July 31, 2013 (14 CFR 121.436(d)).

Hours You Need for an Unrestricted ATP

To earn a standard unrestricted ATP certificate with an airplane category and class rating, 14 CFR 61.153(a)(1) and 14 CFR 61.159(a) require you to be at least 23 years of age and log at least 1,500 hours of total time as a pilot.

By our calculation from 14 CFR 61.159(a), the 500-hour cross-country minimum accounts for one-third of the 1,500 total hours required, and the 250-hour Pilot in Command requirement accounts for one-sixth of the total hours. The table below details every flight time requirement and simulator credit allowance under 14 CFR 61.159.

Unrestricted ATP Aeronautical Experience Requirements (14 CFR 61.159)

Experience Category Minimum Hours Permitted Simulator or Substitution Credits
Total time as a pilot 1,500 hours Up to 100 hours total in an FFS or FTD representing an airplane in an approved Part 121, 135, 141, or 142 course (14 CFR 61.159(a)(6)).
Cross-country flight time 500 hours Reduced to 200 hours if applying for a Restricted Privileges ATP under 14 CFR 61.160.
Night flight time 100 hours After 20 night full-stop takeoffs and landings, each additional night full-stop takeoff and landing substitutes for 1 hour, up to 25 hours (14 CFR 61.159(b)).
Class of airplane sought 50 hours Up to 25 hours of training in an FFS representing the class of airplane in an approved Part 121, 135, 141, or 142 course. No FTD or ATD allowed (14 CFR 61.159(a)(3)).
Instrument flight time (actual or simulated) 75 hours Up to 25 hours in an FFS or FTD representing an airplane, or up to 50 hours if completed in a certificated Part 142 training center course (14 CFR 61.159(a)(4)).
Airplane PIC (or SIC performing PIC duties under supervision) 250 hours Must include at least 100 hours of cross-country time and 25 hours of night flight time (14 CFR 61.159(a)(5)(i)).

Restricted Privileges ATP (R-ATP) Pathways

Under 14 CFR 61.153(a)(2) and 14 CFR 61.160, eligible pilots who are at least 21 years old may apply for a Restricted Privileges ATP certificate with an airplane category multiengine class rating or concurrently with a multiengine airplane type rating. An R-ATP holder may serve as Second in Command in Part 121 domestic, flag, and supplemental operations not requiring more than two pilot flightcrew members (14 CFR 61.167(b)).

Every R-ATP pathway under 14 CFR 61.160(e) and (f) lowers the cross-country requirement from 500 hours to 200 hours, while requiring the remaining night, class, instrument, and 250-hour PIC minimums of 14 CFR 61.159. By our calculation from 14 CFR 61.159 and 61.160, the R-ATP rule reduces required cross-country flight time by 300 hours (60 percent) across all four tracks, and cuts required total pilot time by 50 percent for qualified U.S. military pilots (750 hours versus 1,500 hours) and by 33.3 percent for qualifying four-year aviation bachelor's degree graduates (1,000 hours versus 1,500 hours).

To qualify for a university-based R-ATP under 14 CFR 61.160(b), (c), or (d), your institution must hold an FAA Letter of Authorization under 14 CFR 61.169. You must complete your commercial and instrument ground training in an approved Part 141 curriculum at that institution, complete flight training in that curriculum or at a Part 141 school holding a training agreement under 14 CFR 141.26, and present official transcripts or certifying documentation at your practical test.

Restricted Privileges ATP (R-ATP) Pathways (14 CFR 61.160)

Pathway Minimum Total Time Minimum Cross-Country Minimum Age Key Qualification Requirements
U.S. Military Pilot (14 CFR 61.160(a)) 750 hours 200 hours 21 years Form DD-214 showing honorable discharge or official record of active service, plus official record of graduation from a U.S. Armed Forces undergraduate pilot training school as a rated military pilot.
Bachelor's Degree in Aviation (14 CFR 61.160(b)) 1,000 hours 200 hours 21 years Bachelor's degree with an aviation major from a 14 CFR 61.169 authorized institution, 60 semester credit hours of recognized aviation coursework, and integrated Part 141 commercial/instrument training.
Associate's or Partial Credit Degree (14 CFR 61.160(c)-(d)) 1,250 hours 200 hours 21 years Associate's degree with an aviation major (or Bachelor's degree with 30 to 59 recognized aviation credit hours) from a 14 CFR 61.169 authorized institution, at least 30 semester credit hours of recognized coursework, and integrated Part 141 commercial/instrument training.
Age 21 to 22 with Full Hours (14 CFR 61.160(f)) 1,500 hours 200 hours 21 years Meets the 1,500-hour total time and all other 14 CFR 61.159 aeronautical experience minimums, with at least 200 hours of cross-country time.

Worked Example: Auditing Your Logbook for R-ATP Eligibility

Worked example created by our team. The pilot profile below is invented to show how you should calculate your own hours against 14 CFR 61.159 and 61.160 before an airline logbook review.

Suppose you are a 21-year-old flight instructor with a qualifying 60-credit aviation bachelor's degree and integrated Part 141 commercial and instrument training. Your logbook shows 1,015 hours total time, 215 hours cross-country, 90 hours night (with 35 night full-stop takeoffs and landings), 30 hours in multiengine airplanes, 60 hours instrument in airplanes, 20 hours simulated instrument in a Part 141 FTD, and 260 hours airplane PIC (with 110 hours PIC cross-country and 30 hours PIC night).

  • Total and cross-country time: Under 14 CFR 61.160(b) and (e), your degree qualifies you for the 1,000-hour total and 200-hour cross-country minimums. At 1,015 total and 215 cross-country hours, you pass both.
  • Night time: 14 CFR 61.159(a)(2) requires 100 night hours, leaving you 10 hours short. Under 14 CFR 61.159(b), each night full-stop takeoff and landing beyond 20 credits 1 hour of night time, up to 25 hours. Your 15 extra night full-stop landings add 15 hours, bringing your qualifying night total to 105 hours (and adding the ICAO limitation under 14 CFR 61.159(e) until you log 100 actual night hours).
  • Instrument and PIC time: 14 CFR 61.159(a)(4) requires 75 instrument hours (at most 25 hours in an FFS or FTD outside Part 142). Your 60 airplane hours plus 20 FTD hours equal 80 qualifying hours. Your 260 airplane PIC hours (110 cross-country, 30 night) meet the 250-hour PIC, 100-hour PIC cross-country, and 25-hour PIC night rules in 14 CFR 61.159(a)(5).
  • Multiengine class time: 14 CFR 61.159(a)(3) requires 50 hours in class, leaving you 20 hours short. Because you may credit up to 25 hours of Full Flight Simulator training in an approved Part 121 initial training course, completing 20 FFS hours in airline training fulfills the 50-hour requirement.

What the 40-Hour ATP CTP Course Covers

Under 14 CFR 61.153(e) and 61.156, you must complete the FAA-approved ATP Certification Training Program (ATP CTP) with an authorized Part 121, 135, 141, or 142 provider before taking the ATP multiengine knowledge test.

Under 14 CFR 61.156(a) and (b) and 78 FR 42324, the 40-hour curriculum splits into at least 30 hours of academic training and at least 10 hours in a Flight Simulation Training Device (at least 6 hours in a Level C or higher Full Flight Simulator and up to 4 hours in a Level 4 or higher Flight Training Device):

  • Aerodynamics (at least 8 academic hours): High-altitude operations and aerodynamics.
  • Meteorology (at least 2 academic hours): Adverse weather phenomena and weather detection systems.
  • Air carrier operations (at least 14 academic hours): Physiology, communications, checklist philosophy, operational control, minimum equipment list (MEL) and configuration deviation list (CDL), ground operations, turbine engines, transport category performance, and automation, navigation, and flight path warning systems.
  • Leadership and CRM (at least 6 academic hours): Leadership, professional development, crew resource management, and safety culture.
  • Full Flight Simulator training (at least 6 FSTD hours): Conducted in a Level C or higher FFS representing a multiengine turbine airplane with a maximum takeoff weight of 40,000 pounds or greater, covering low energy states/stalls, upset recovery techniques, and adverse weather conditions including icing, thunderstorms, and crosswinds with gusts.
  • Flight Training Device or FFS training (up to 4 remaining FSTD hours): Completed in a Level 4 or higher FSTD, covering navigation including flight management systems (FMS) and automation including autoflight.

Pre-Employment Screening and Pilot Records Database (PRD) Checklist

Under 14 CFR 111.5, the Pilot Records Improvement Act (PRIA) ceased to be effective on September 9, 2024, and was replaced by the electronic Pilot Records Database (PRD) under 14 CFR Part 111. Under 14 CFR 111.105, no Part 121 air carrier may permit you to begin service as a pilot until it has evaluated your FAA records, previous reporting entity records, 5-year employment history, and state motor vehicle driving records.

Checklist written by our team from 14 CFR Part 111 Subpart B and Subpart D. Complete these six steps before your interview and onboarding date:

  • Step 1, Apply for electronic PRD access early: Under 14 CFR 111.305(c), submit your electronic access application to the FAA at least 7 days before seeking to access the PRD, with your full name as shown on your pilot certificate, FAA certificate number, mailing address, telephone number, and email address.
  • Step 2, Audit your FAA records in the PRD: Under 14 CFR 111.315 and 111.135, review your current pilot and medical certificates, type ratings and limitations, any failed Part 61 practical test, unoverturned enforcement findings, aviation accidents or incidents as PIC or SIC, and DOT drug and alcohol testing history (verified positive drug tests, alcohol misuse violations of 0.04 or greater, and refusals to test).
  • Step 3, Review previous employer reporting records: Check training, qualification, and proficiency records (including check pilot comments and unsatisfactory tasks under 14 CFR 111.225), final disciplinary action records related to pilot performance (14 CFR 111.230), and final separation from employment records (14 CFR 111.235). Flight/duty/rest records, medical exam records, and protected Voluntary Safety Reporting Program (Part 193) records are prohibited from being reported (14 CFR 111.225(b) and 111.245).
  • Step 4, Report inaccuracies immediately: Under 14 CFR 111.320 and 111.250, report any error through the PRD. The reporting entity must correct an identified inaccuracy within 10 days or initiate a dispute investigation within 30 days.
  • Step 5, Affirm your 5-year employment history and grant PRD consent: Under 14 CFR 111.310(a) and (b), provide written consent in the database and affirm that your employment history for the preceding 5 years is accurate and complete.
  • Step 6, Sign your National Driver Register (NDR) consent: Under 14 CFR 111.110 and 111.310(c), provide separate written consent authorizing an NDR search for your state driving records. Under 14 CFR 111.120(c), the carrier must provide copies of any state driving records obtained within 30 days of your request.

Part 121 Initial Training, Line Milestones, and Certificate Limitations

Once hired by a Part 121 carrier, you must complete initial ground and flight training for the airplane type and crewmember position under 14 CFR 121.433(a), including approved Crew Resource Management training (14 CFR 121.404) and extended envelope training in a Full Flight Simulator (14 CFR 121.423). During early line flying, you must satisfy four operational milestones under 14 CFR Part 121 Subpart O:

  • Operations familiarization (14 CFR 121.435): Newly hired Part 121 pilots who began basic indoctrination ground training on or after April 27, 2022, must complete at least 2 operating cycles in the flight deck observer seat with an operational headset before beginning operating experience.
  • Operating experience (14 CFR 121.434(c)): As a Second in Command completing initial training in Group II turbojet airplanes, you must perform SIC duties in flight under a check pilot's supervision for at least 25 hours (20 hours in Group I turboprops, 15 hours in Group I reciprocating airplanes), including at least 4 operating cycles with at least 2 cycles as the pilot flying.
  • Consolidation of knowledge and skills (14 CFR 121.434(g)): After passing your practical test or proficiency check, you must log at least 100 hours of line operating flight time (including operating experience) within 120 days, extendable to at most 150 days with refresher training or a supervised check pilot observation flight on or before day 120.
  • High-minimums SIC pairing limits (14 CFR 121.438): Until you have 100 hours as Second in Command in Part 121 operations in that airplane type, the Pilot in Command (unless a qualified check pilot) must make all takeoffs and landings at designated special airports, and whenever prevailing visibility is at or below 3/4 mile, runway visual range (RVR) is at or below 4,000 feet, the runway has water, snow, or slush, braking action is reported as less than good, the crosswind component exceeds 15 knots, or windshear is reported in the vicinity. Either the PIC or SIC must also have at least 75 hours of line operating flight time in that airplane type.

SIC PDP, Flight Engineer Credits, and Removing Certificate Limitations

Under 14 CFR 61.159(c), a commercial pilot employed by a Part 135 operator may log Second in Command time toward the 1,500-hour ATP or R-ATP total time requirements when a second pilot is not otherwise required, if conducted under an FAA-approved Part 135.99 Second in Command Professional Development Program (SIC PDP) and certified by the PIC. It cannot be counted toward the 250-hour PIC requirement. Under 14 CFR 61.159(d), qualifying Part 121 or U.S. Armed Forces flight engineers may credit 1 hour for each 3 hours of flight engineer time toward total ATP time, up to 500 hours.

Using the night landing substitution (14 CFR 61.159(b)), SIC PDP credit (14 CFR 61.159(c)), flight engineer credit (14 CFR 61.159(d)), or R-ATP reduced hours (14 CFR 61.160(a) through (d)) places an ICAO limitation on your certificate. Under 14 CFR 61.159(f) and 61.160(g)-(h), the FAA removes both the R-ATP restriction and the ICAO limitation once you present satisfactory evidence of meeting the full 14 CFR 61.159 experience requirements and the 23-year-old age requirement.

Practice example

Once you finish initial training and start flying the line as a new First Officer with fewer than 100 hours in the airplane type, under what conditions does 14 CFR 121.438 require the Captain to make the takeoff and landing?

Example answer, written by us. It is not a real applicant's story. Under 14 CFR 121.438, during my first 100 hours of line operating flight time as Second in Command in the airplane type, if I am flying with a regular line Captain who is not a qualified check pilot, the Captain must make all takeoffs and landings at any special airport designated by the FAA or the airline. In addition, the Captain must make the takeoff and landing whenever weather or runway conditions hit six specific triggers. First, the Captain flies if prevailing visibility in the latest weather report is at or below 3/4 mile, or if runway visual range for the runway in use is at or below 4,000 feet. Second, the Captain must fly if the runway is contaminated with water, snow, slush, or similar conditions that affect performance, or if reported braking action is less than good. Third, the Captain takes the controls if the crosswind component exceeds 15 knots, or if windshear is reported in the vicinity of the airport. Before every departure and approach briefing during my first 100 hours, I will actively check our weather and runway state against those numbers so there is zero ambiguity about who is the pilot flying.

This answer states the exact regulatory citation (14 CFR 121.438), notes the check pilot exception, and lists every numerical weather and runway limitation accurately. Ending with how the First Officer applies the rule during pre-departure and approach briefings shows practical Crew Resource Management.

Practice this on Fourstripe. Pick your airline and a captain runs the interview out loud: TMAAT, about-you, technical and scenario questions, with real follow-ups. You get a scored report on every answer. 7-day trial, then from $149 a week. Start a practice interview

Frequently asked questions

What pilot certificate and ratings are required to fly as a First Officer at a Part 121 airline?

Under 14 CFR 121.436(b) and 78 FR 42324, a First Officer (Second in Command) in Part 121 operations must hold an Airline Transport Pilot (ATP) certificate or Restricted Privileges ATP (R-ATP) certificate, an appropriate aircraft type rating for the aircraft being flown, and at least a second-class medical certificate. A second-in-command type rating obtained under 14 CFR 61.55 does not satisfy Part 121 requirements.

How many flight hours do I need to qualify for a Restricted Privileges ATP (R-ATP) certificate?

Under 14 CFR 61.160, pilots at least 21 years old may qualify for an R-ATP with 750 hours as a qualified U.S. military pilot, 1,000 hours with an authorized aviation Bachelor's degree and 60 recognized aviation semester credit hours, or 1,250 hours with an authorized aviation Associate's degree (or Bachelor's degree) and at least 30 recognized credit hours. Pilots who are 21 or 22 years old with 1,500 total hours may also obtain an R-ATP with a reduced requirement of 200 hours of cross-country time.

What are the FAA experience requirements to upgrade to Captain at a Part 121 carrier?

Under 14 CFR 121.436(a), a Part 121 Pilot in Command (Captain) must hold an unrestricted ATP certificate, an appropriate aircraft type rating, a first-class medical certificate, and at least 1,000 hours of qualifying air carrier experience (such as Part 121 SIC time or qualifying Part 135/91K PIC time). Up to 500 hours of multiengine turbine multi-pilot military PIC time may be credited toward the 1,000-hour requirement under 14 CFR 121.436(c).

What background records are checked through the Pilot Records Database (PRD) during airline hiring?

Under 14 CFR 111.105, 111.110, and 111.135, hiring carriers must evaluate your FAA certificate and medical records, failed Part 61 practical tests, unoverturned enforcement actions, accidents and incidents, DOT drug and alcohol testing history, previous employer training, disciplinary, and separation records, your 5-year employment history, and National Driver Register state driving records. You must apply for PRD access at least 7 days before seeking to access the database and provide written consent before the carrier can access your file.

Can I use an expired ATP knowledge test when hired by a Part 121 airline?

Yes. Under 78 FR 42324, the ATP knowledge test has a five-year validity period for pilots who pass the test after completing the ATP CTP, and new hire pilots in Part 121 operations may use an expired knowledge test if they have completed the ATP CTP and the operator's initial training program.

Sources