IFR Holding Speeds, Entries & Lost Comms (AVEF/MEA) Guide
Short answer: Under FAA AIP ENR 1.5 and AIM 5-3-8, standard civil maximum holding airspeeds are 200 KIAS from the minimum holding altitude (MHA) to 6,000 feet MSL, 230 KIAS from 6,001 to 14,000 feet MSL, and 265 KIAS at 14,001 feet MSL and above. When 3 minutes or less from a clearance limit without onward clearance, pilots must begin reducing speed to cross the fix at or below the holding speed. If two-way radio communications fail, pilots follow the AVEF routing and MEA altitude hierarchy under 14 CFR 91.185.
FAA Maximum Holding Airspeeds and Speed Exceptions
Under FAA Aeronautical Information Publication (AIP) ENR 1.5 and the Instrument Procedures Handbook (FAA-H-8083-16B), holding protected airspace is sized directly based on indicated airspeed.
When an aircraft is 3 minutes or less from a clearance limit and a clearance beyond the fix has not been received, you must begin a speed reduction to cross the fix initially at or below the maximum holding airspeed. Under FAA Order JO 7110.65BB Section 4-6-1, controllers must issue holding instructions at least 5 minutes before the aircraft reaches the clearance limit when delay is expected.
If turbulence or icing requires you to exceed maximum holding airspeed, advise ATC immediately and request an alternate clearance, because exceeding the speed limit can take your aircraft outside protected airspace. For flight operations in Canadian airspace, flight crews refer to the Transport Canada Aeronautical Information Manual (TC AIM, TP 14371), which Transport Canada updates twice a year to provide rules and procedures. Exceeding maximum holding airspeeds without ATC clearance risks departing protected airspace.
FAA Maximum Holding Airspeeds and Exceptions (FAA AIP ENR 1.5, Table ENR 1.5-1)
| Application or Altitude Band | Maximum Airspeed (KIAS) | Operational Rules and Chart Depiction |
|---|---|---|
| MHA to 6,000 feet MSL | 200 KIAS | Standard civil maximum airspeed |
| 6,001 to 14,000 feet MSL | 230 KIAS | Standard civil maximum, may be restricted to 210 KIAS by charted icon |
| 14,001 feet MSL and above | 265 KIAS | Standard civil maximum airspeed |
| Charted Parenthetical Limit | As published, e.g., (175) KIAS | Shown in parentheses inside racetrack symbol, cross fix at or below speed |
| Climb-in-Hold Procedure | n/a | Allowed when climb-in-hold is published, unless lower speed is charted |
| USAF Airfields Only | 310 KIAS | Standard limit at USAF fields unless otherwise depicted |
| US Navy Airfields Only | 230 KIAS | Standard limit at Navy fields unless otherwise depicted |
Holding Pattern Entries, Bank Angles, and Wind Drift
Holding protected airspace is built on pilot compliance with three FAA-recommended entry procedures: Parallel, Teardrop, and Direct. Standard holding patterns use right-hand turns, while nonstandard patterns use left-hand turns at both the fix end and outbound end.
You select your entry sector based on your aircraft heading upon arrival at the holding fix. Entry procedures for a nonstandard left-turn pattern relate to the 70-degree line on the holding side exactly like a standard right-turn pattern.
To compensate for crosswind drift on straight legs, FAA AIP ENR 1.5 instructs you to triple your inbound drift correction on the outbound leg in the opposite direction.
- Parallel entry (Sector a): Fly to the fix, turn to a heading that parallels the holding course outbound on the nonholding side for 1 minute, turn in the direction of the holding pattern through more than 180 degrees, and return to the holding fix or intercept the inbound course.
- Teardrop entry (Sector b): Fly to the fix, turn outbound to a heading for a 30-degree teardrop entry within the pattern on the holding side for 1 minute, and then turn in the direction of the pattern to intercept the inbound holding course.
- Direct entry (Sector c): Fly directly to the holding fix and turn immediately to follow the racetrack pattern.
- VOR station passage: When holding at a VOR, begin the turn to the outbound leg at the first complete reversal of the to-from indicator.
Holding Pattern Timing, DME Legs, and ATC Clearances
In a timed hold, your target is always the inbound leg duration. At or below 14,000 feet MSL, the inbound leg is 1 minute. Fly the initial outbound leg for 1 minute or 1 1/2 minutes based on altitude, then adjust subsequent outbound legs to achieve the target inbound time.
Outbound leg timing begins over or abeam the holding fix, whichever occurs later. If you cannot determine the abeam point, start timing when the turn to outbound is completed. When Distance Measuring Equipment (DME) or Along-Track Distance (ATD) is specified instead of time, use the same entry methods, but end the outbound leg at the controller-assigned or charted mileage readout.
If ATC clears you to a fix where a pattern is charted on your route, the controller may issue the holding direction and state 'as published' along with an Expect Further Clearance (EFC) time. If no hold is charted and ATC has not issued instructions, request instructions before reaching the fix. If you cannot reach ATC due to frequency congestion, enter a standard holding pattern on your inbound course to the fix and request clearance as soon as possible.
- Six components of a non-charted holding clearance (FAA AIP ENR 1.5): (1) Direction of holding from fix using cardinal compass points, (2) Holding fix, (3) Radial, course, or airway to hold on, (4) Leg length in miles if DME or RNAV, or minutes if requested or needed, (5) Turn direction if left turns are required, and (6) Expect Further Clearance (EFC) time.
- Mandatory holding reports (AIM 5-3-3): Without an ATC request, report the time and altitude upon reaching an assigned holding fix, and report when leaving any assigned holding fix.
- Instrument Rating ACS standards (FAA-S-ACS-8C, November 2023): During holding tasks, maintain airspeed within plus or minus 10 knots, altitude within plus or minus 100 feet, heading within plus or minus 10 degrees, and track the inbound course within three-quarter scale deflection of the CDI.
RNAV Systems and STAR Holding Considerations
Technical interviews often explore how Flight Management Systems (FMS) and RNAV units fly holding patterns. According to FAA AIP ENR 1.5, holding protected airspace remains based on conventional NAVAID design, which assumes an aircraft flies directly over the fix upon entry. However, RNAV systems may initiate a fly-by turn prior to the fix, potentially creating excursions beyond protected airspace during a direct entry from the holding side if intercept angles and ground speeds are high.
When using RNAV lateral guidance, the system uses the assigned leg distance as the maximum length of the inbound leg and computes an outbound turn point to achieve that length. In a strong headwind on the outbound leg, an RNAV system can drift beyond the design turn point before turning inbound. If your flight guidance system has a selectable bank angle limit, keep it set to a minimum of 25 degrees regardless of altitude unless aircraft operating limitations require otherwise and ATC is notified.
Watch how your avionics handle altitude transitions. Loading a hold above 14,000 feet MSL when descending to hold below 14,000 feet MSL may cause the RNAV system to mistakenly apply 1 1/2 minute timing below 14,000 feet. Under FAA AIP ENR 1.5, pilots must ensure the RNAV system applies the proper time and speed restrictions to a holding pattern, especially when climbing or descending to a holding pattern altitude where time and speed restrictions differ from the aircraft's present altitude. On Standard Terminal Arrival Routes (STARs), published speed restrictions are mandatory unless modified by ATC. Charted expect altitudes and speeds on a STAR are for planning purposes only and must not be used in lost communications unless ATC verbally issued them as part of a further clearance.
- Ground track vs heading: Many RNAV systems calculate entry sectors using ground track rather than heading, which can lead to a different entry selection in strong crosswinds.
- DME slant range substitution: Using RNAV distance to replace DME distance is authorized, and the difference caused by the lack of slant range is considered negligible.
- Arrival holding patterns: Approach charts sometimes depict arrival holding with a thin line at an Initial Approach Fix. Unlike a bold hold-in-lieu of procedure turn, a thin-line arrival hold is not authorized unless explicitly cleared by ATC.
FAR 91.185 Lost Communications: Route, Altitude, and Clearance Limits
Lost communications questions test 14 CFR 91.185 (AIM 6-4-1). Your immediate cockpit actions are to squawk Mode A/3 Code 7600, monitor NAVAID voice features, and attempt to reestablish contact on your previous frequency, on 121.5 MHz, or with a Flight Service Station (FSS). If you suspect an ARTCC frequency outage after changing channels, AIM 5-3-1 advises waiting at least 1 minute because backup transceiver switchover rarely exceeds 60 seconds.
If radio failure occurs in VFR conditions, or if VFR conditions are encountered at any point after the failure (even in Class A airspace), continue the flight under VFR and land as soon as practicable. AIM 6-4-1 explains that landing as soon as practicable does not mean as soon as possible. You retain pilot judgment and do not need to land at an unsuitable airport or minutes short of your destination.
In IFR conditions where VFR cannot be maintained, follow the route and altitude sequence in 14 CFR 91.185(c). Select the route in order using the AVEF mnemonic: Assigned, Vectored, Expected, or Filed. For altitude, fly the highest of the MEA mnemonic levels: Minimum IFR Altitude, Expected, or Assigned for the segment being flown.
- Assigned route: Fly the route assigned in the last ATC clearance.
- Vectored route: If being radar vectored, fly direct from the point of failure to the fix, route, or airway specified in the vector clearance.
- Expected route: In the absence of an assigned route, fly the route ATC advised may be expected in a further clearance.
- Filed route: In the absence of an assigned or expected route, fly the route filed in your flight plan.
- Altitude selection: Fly the highest of your assigned altitude, the minimum altitude for IFR operations (such as MEA or MOCA within 22 NM of a VOR), or your expected altitude, adjusting for each route segment.
- Leaving an approach clearance limit: When the clearance limit is a fix from which an approach begins, start descent and approach as close as possible to the EFC time, or if no EFC was received, as close as possible to your ETA based on your filed or amended ETE.
- Leaving a non-approach clearance limit: When the clearance limit is not a fix from which an approach begins, leave at the EFC time, or upon arrival over the fix if no EFC was received, proceed to an approach fix, and start descent and approach as close as possible to your calculated ETA.
Worked Example: DME Math, Wind Drift, and Lost Comms Altitudes
Technical interviews test practical application using flight scenarios. Below is a three-part worked example based on FAA AIP ENR 1.5 and AIM 6-4-1.
Part 1 (DME Holding Leg Math): If holding at a fix on the 10 NM DME fix with an inbound course toward the NAVAID and a 5 NM leg length, you fly away from the station on the outbound leg. Turn inbound when the DME reads 15 NM (10 NM plus 5 NM). If your inbound course is away from the station with the holding fix at 28 NM DME and an 8 NM leg length, fly toward the station outbound and turn inbound when the DME reads 20 NM (28 NM minus 8 NM).
Part 3 (Lost Comms Altitudes): You are cleared via fixes A, B, C, D, to E. MEAs are 5,000 feet between A and B, 5,000 feet between B and C, 11,000 feet between C and D, and 7,000 feet between D and E. Cruising at an assigned altitude of 6,000 feet between A and B, ATC advises you to expect 8,000 feet at B. Your radios fail before reaching B. Maintain 6,000 feet until B (highest of 6,000 assigned and 5,000 MEA), climb to 8,000 feet at B (the expected altitude), and climb to 11,000 feet approaching C to satisfy the 11,000-foot MEA. At D, where the MEA drops to 7,000 feet, descend back to 8,000 feet because 8,000 feet remains the highest of the three rule altitudes for the segment from D to E.
Technical Interview Response Strategy
In technical interviews, state the regulation or source first, provide the precise number, and then explain cockpit management. Mention calculating holding fuel burn, coordinating with the other pilot, and notifying ATC promptly if aircraft parameters require higher airspeeds or larger bank angles.
Practice example
You are flying in IMC at 10,000 feet MSL approaching your clearance limit fix, which is not an initial approach fix for your destination. You have not received a further clearance or an EFC time, and you discover you have lost two-way radio communications. Walk me through your speed reduction and your actions at the fix.
Example answer, written by us. It is not a real applicant's story. First, when 3 minutes or less from the clearance limit without an onward clearance, FAA AIP ENR 1.5 expects me to begin slowing down to cross the fix at or below the maximum holding airspeed for 10,000 feet MSL, which is 230 KIAS, or 210 KIAS if a nonstandard holding icon is charted. After discovering a two-way radio communications failure, I squawk 7600, check my audio panel, monitor NAVAID voice, and attempt contact on the previous frequency, 121.5 MHz, or through Flight Service. Because I remain in IMC, I follow 14 CFR 91.185 and AIM 6-4-1. Since my clearance limit is not a fix from which an approach begins and no Expect Further Clearance time was issued, I do not enter holding. Instead, upon arrival over the clearance limit, I leave it immediately via my expected or filed route, proceed to an approach fix, and commence descent and approach as close as possible to my calculated ETA.
This answer directly solves both regulatory requirements by applying the standard 3-minute deceleration window and 230 KIAS speed limit (FAA AIP ENR 1.5), followed by the exact 14 CFR 91.185(c)(3)(ii) procedure for departing a non-approach clearance limit when no EFC was issued.
Practice this on Fourstripe. Pick your airline and a captain runs the interview out loud: TMAAT, about-you, technical and scenario questions, with real follow-ups. You get a scored report on every answer. 7-day trial, then from $149 a week. Start a practice interview
Frequently asked questions
When should a pilot reduce speed before entering a hold?
According to FAA AIP ENR 1.5 and AIM 5-3-8, pilots should begin a speed reduction when 3 minutes or less from the clearance limit if an onward clearance has not been received.
What transponder code is used during two-way radio communications failure?
Under AIM 6-4-2, pilots experiencing two-way radio communications failure should squawk Mode A/3 Code 7600.
What altitude is flown during IFR lost communications?
Under 14 CFR 91.185 and AIM 6-4-1, pilots must fly the highest of their assigned altitude, the minimum IFR altitude for the route segment, or the expected altitude received in a further clearance.
When does a pilot leave a clearance limit during lost communications?
If the clearance limit is an approach fix, begin descent and approach at the EFC time or filed ETA. If it is not an approach fix, leave at the EFC time or upon reaching the fix if no EFC was given, and proceed to an approach fix.
Sources
- FAA AIP ENR 1.5: Holding, Approach, and Departure Procedures
- FAA AIM Chapter 5, Section 3: En Route Procedures
- FAA AIM Chapter 6, Section 4: Two-way Radio Communications Failure
- FAA Order JO 7110.65BB Chapter 4, Section 6: Holding Aircraft
- FAA Instrument Procedures Handbook (FAA-H-8083-16B)
- FAA Instrument Rating Airplane Airman Certification Standards (FAA-S-ACS-8C)
- GovInfo: 14 CFR 91.185 IFR Operations: Two-Way Radio Communications Failure (2026)
- Transport Canada Aeronautical Information Manual (TC AIM, TP 14371)