JSX Pilot Requirements: FAA Part 135 Qualifications for Captains and First Officers
Short answer: If your goal is to fly as a pilot for JSX, flight operations are conducted under 14 CFR Part 135 commuter regulations. Under 14 CFR 135.243 and 135.245, a Captain (Pilot in Command) on multiengine commuter aircraft with 10 or more passenger seats must hold an Airline Transport Pilot (ATP) certificate with at least 1,500 total flight hours under 14 CFR 61.159, while a First Officer (Second in Command) must hold at least a Commercial Pilot Certificate with appropriate category and class ratings and an instrument rating. Check current open pilot requisitions directly on the official careers portal to confirm specific experience minimums for your track.
How Part 135 operating rules set pilot minimums
If your goal is to fly for JSX, flights are conducted under 14 CFR Part 135. Under Department of Transportation regulations in 14 CFR Part 380, flights may be sold as public charters while operated by a direct air carrier under 14 CFR Part 135 commuter authority.
This distinction matters for your logbook. Because commuter public charter flights operate under Part 135 rather than Part 121, the Federal Aviation Regulations set different baseline certificate requirements for the left seat and the right seat. Under 14 CFR 135.99, no certificate holder may operate an aircraft without a second in command if that aircraft has a passenger seating configuration, excluding any pilot seat, of ten seats or more.
In addition, FAA Part 135 regulations require a flight attendant crewmember on board any aircraft with a passenger seating configuration of more than 19 seats under 14 CFR 135.107. In multiengine passenger operations with 10 or more passenger seats, you fly as part of a two-pilot flight deck crew alongside cabin crew, often operating out of fixed base operator (FBO) facilities rather than main commercial airport concourses.
FAA baseline pilot requirements for Part 135 commuter operations with 10 or more passenger seats as of November 2026
| Requirement area | Pilot in Command (Captain) | Second in Command (First Officer) |
|---|---|---|
| Governing regulation | 14 CFR 135.243 and 14 CFR 61.159 | 14 CFR 135.245 |
| Minimum pilot certificate | Airline Transport Pilot (ATP) certificate | Commercial Pilot Certificate |
| Required ratings | Airplane category, multiengine class, and aircraft type rating | Airplane category, multiengine class, and instrument rating |
| FAA total time baseline | 1,500 hours total time as a pilot for standard ATP | Met via Commercial Pilot certification under Part 61 |
| Commuter operating experience | 25 hours in turbojet or 20 hours in turbine multiengine under 14 CFR 135.244 | Not required under 14 CFR 135.244 |
First Officer (Second in Command) FAA requirements
Under 14 CFR 135.245, no certificate holder may use any person, nor may any person serve, as Second in Command (SIC) of an aircraft unless that pilot holds at least a Commercial Pilot Certificate with appropriate category and class ratings and an instrument rating. For multiengine turbine airplanes operating under Instrument Flight Rules (IFR), you need an airplane category, multiengine land class rating, and airplane instrument rating.
Notice what 14 CFR 135.3(b) says about training and qualifications for two-pilot commuter airplanes. While certificate holders conducting commuter operations with airplanes that require two pilots by type certification must comply with Subparts N and O of Part 121 instead of Subparts E, G, and H of Part 135, the rule includes an explicit exception for First Officers. Specifically, a pilot serving as Second in Command in that commuter operation may meet the requirements of 14 CFR 135.245 instead of the Part 121 SIC ATP rules in 14 CFR 121.436.
For eligible on-demand operations defined under 14 CFR 135.4, the FAA sets a baseline of 500 hours of total flight time for a Second in Command, along with a commercial pilot certificate and instrument ratings for multiengine turbine-powered fixed-wing aircraft. Under 14 CFR 135.4, if a Second in Command has fewer than 100 hours of flight time as SIC in the aircraft make, model, and type being flown, and the Pilot in Command is not a qualified check pilot, the Pilot in Command must make all takeoffs and landings in specific challenging conditions. Those conditions include prevailing visibility at or below 3/4 mile, runway visual range at or below 4,000 feet, contaminated runways with water, snow, slush, or ice, braking action reported as less than good, crosswind components exceeding 15 knots, reported windshear in the vicinity, or whenever a Destination Airport Analysis is required by 14 CFR 135.385(f).
To serve as Second in Command under IFR, you must also maintain instrument recency under 14 CFR 135.245 by meeting specific experience requirements within the preceding 6 calendar months:
- Six instrument approaches performed and logged within the 6 calendar months preceding the month of the flight.
- Holding procedures and tasks performed in actual weather conditions or under simulated instrument conditions using a view-limiting device.
- Intercepting and tracking courses through the use of navigational electronic systems.
- Simulator option: You may complete these instrument tasks in an approved Flight Simulation Training Device (FSTD) representing the aircraft category, provided a flight instructor qualified under 14 CFR 135.338 or a check pilot qualified under 14 CFR 135.337 observes the session and signs your logbook or training record.
- Reestablishing recency: If you lapse on instrument currency for more than 6 calendar months, 14 CFR 135.245 requires you to reestablish recency under a qualified Part 135 instructor or check pilot across six specific areas of operation: air traffic control clearances and procedures, flight by reference to instruments, navigation systems, instrument approach procedures, emergency operations, and postflight procedures.
Captain (Pilot in Command) FAA requirements
To act as Pilot in Command (PIC) of a turbojet airplane, an airplane having a passenger-seat configuration of 10 seats or more, or a multiengine airplane in a commuter operation under 14 CFR 135.243, you must hold an Airline Transport Pilot (ATP) certificate with appropriate category and class ratings and an appropriate type rating for that airplane.
To earn a standard unrestricted airplane ATP certificate under 14 CFR 61.159, you must log specific aeronautical experience minimums.
- 1,500 hours of total time as a pilot.
- 500 hours of cross-country flight time.
- 100 hours of night flight time. If you have performed at least 20 night takeoffs and landings to a full stop, you may substitute each additional night takeoff and landing to a full stop for 1 hour of night flight time, up to 25 hours of credit under 14 CFR 61.159.
- 50 hours of flight time in the class of airplane for the rating sought (multiengine land). Up to 25 hours of training in a full flight simulator representing the class of airplane may be credited if completed as part of an approved training course under Parts 121, 135, 141, or 142.
- 75 hours of instrument flight time in actual or simulated instrument conditions. You may credit up to 25 hours of simulated instrument time in a full flight simulator or flight training device, or up to 50 hours if completed in a Part 142 certificated training center course.
- 250 hours of flight time in an airplane as Pilot in Command, or as Second in Command performing the duties of PIC under the supervision of a PIC, or any combination thereof. This 250-hour block must include at least 100 hours of cross-country time and 25 hours of night flight time.
- Simulator cap: No more than 100 hours of the total aeronautical experience requirement may be obtained in a full flight simulator or flight training device representing an airplane as part of an approved training course.
Commuter operating experience and 90-day currency rules
Holding an ATP and a type rating is not the final step before commanding a passenger flight. Under 14 CFR 135.244, a pilot may not serve as Pilot in Command of an aircraft in a commuter operation unless that pilot has completed specific operating experience in that make and basic model aircraft and in the PIC crewmember position prior to designation.
For a multiengine turbine-powered aircraft, 14 CFR 135.244 requires 20 hours of operating experience. For a turbojet-powered airplane, 14 CFR 135.244 requires 25 hours of operating experience. You must acquire this time in flight during commuter passenger-carrying operations after satisfactorily completing ground and flight training, while performing the duties of a PIC under the supervision of a qualified check pilot. Under 14 CFR 135.244, you can reduce these required hours by up to 50 percent by substituting one additional takeoff and landing for each hour of flight. By our calculation from 14 CFR 135.244, that 50 percent substitution reduces the minimum in-flight operating experience to 12.5 hours for a turbojet airplane and 10 hours for a multiengine turbine airplane.
Once on the line, Captains must also maintain 90-day passenger-carrying currency under 14 CFR 135.247. You must complete three takeoffs and three landings as the sole manipulator of the flight controls in an aircraft of the same category, class, and type within the preceding 90 days. For night flights occurring between 1 hour after sunset and 1 hour before sunrise, those three takeoffs and landings must be made during that night period. However, 14 CFR 135.247 offers an alternative for a PIC of a turbine-powered airplane type certificated for more than one pilot: if you hold at least 1,500 hours of total pilot experience, maintain daytime 90-day currency, and log at least 15 hours of flight time in that aircraft type within the preceding 90 days, you can satisfy night recency by either logging 3 night takeoffs and landings to a full stop within the preceding 6 months, or completing 6 night takeoffs and landings to a full stop in an approved Part 142 simulator program within the preceding 12 months.
Company training, PRIA background checks, and testing
Every Part 135 standard air carrier must vet your background and train you under an FAA-approved curriculum before placing you on the flight deck. Under the Pilot Records Improvement Act of 1996 (PRIA), as detailed on the FAA Part 135 general requirements portal, an air carrier cannot place a pilot into service until after it obtains and reviews the last 5 years of the pilot's background records. You are also subject to mandatory workplace drug and alcohol testing programs administered under 14 CFR Part 120 and 49 CFR Part 40.
Once hired, your company training curriculum covers required segments set by FAA guidance: Basic Indoctrination Training, Emergency Training, Crew Resource Management (CRM) Training, Initial Ground and Flight Training, and Hazardous Materials (hazmat) training. If you later change seats or aircraft, the curriculum includes Upgrade, Recurrent, Requalification, Differences, and Transition training.
To finish training and stay legal on the line, you must pass the knowledge and practical evaluations in 14 CFR 135.293. Since the beginning of the 12th calendar month before service, every pilot must pass a written or oral test given by the FAA Administrator or an authorized check pilot, plus a practical competency check in that type of multiengine or turbojet aircraft.
- Regulations and manuals: Appropriate provisions of 14 CFR Parts 61, 91, and 135, plus the company's Operations Specifications and General Operations Manual (GOM).
- Aircraft systems and limitations: Powerplant, major components and systems, major appliances, performance and operating limitations, standard and emergency operating procedures, and the approved Aircraft Flight Manual.
- Weight and balance: Methods of determining compliance with weight and balance limitations for takeoff, landing, and en route operations.
- Navigation and ATC: Air navigation aids, instrument approach facilities and procedures, and air traffic control IFR procedures.
- Meteorology and severe weather: Principles of frontal systems, icing, fog, thunderstorms, windshear, high-altitude weather, recognizing and avoiding severe weather, and escaping low-altitude windshear.
Worked example: Auditing your logbook for Part 135 eligibility
Before you submit an application to fly for an operator like JSX, compare your current logbook totals against the FAA Part 135 and Part 61 thresholds to see which seat and operational rules apply to you. Below is a worked example written by our team for an invented applicant who holds a Commercial Pilot Certificate with Airplane Multiengine Land and Instrument ratings and has logged 1,350 total hours.
First, check Second in Command eligibility under 14 CFR 135.245. Because our invented pilot holds a Commercial Pilot Certificate with multiengine and instrument ratings, they meet the certificate baseline for a Part 135 First Officer. However, they only logged four instrument approaches in the last 6 calendar months. Before serving as SIC under IFR, they must log at least two more instrument approaches, plus holding and course-intercept tasks if not already logged within the preceding 6 calendar months.
Second, check how close this pilot is to Pilot in Command eligibility under 14 CFR 135.243 and 14 CFR 61.159. Our invented pilot has 1,350 total hours, 460 cross-country hours, 85 night hours (with 35 night full-stop landings), 60 multiengine class hours, 80 instrument hours, and 260 PIC hours. To qualify for the standard unrestricted ATP required for a Captain role under 14 CFR 135.243, this pilot needs 150 more total hours and 40 more cross-country hours. For the 100-hour night requirement, they are 15 hours short on raw night flight time, but because they have more than 20 night takeoffs and landings to a full stop, 14 CFR 61.159 lets them credit their 15 extra night full-stop landings for 15 hours of night time, satisfying the 100-hour night threshold immediately.
Pre-application checklist and how to apply safely
When preparing your application materials, follow the recruitment verification guidance published on the official JSX careers page. Official recruitment notices advise that legitimate job opportunities are posted on the official company careers portal, and official communications from recruiters come directly from an official company email address.
Official hiring guidance notes that operators will never ask for payment, banking details, or personal financial information at any stage of the hiring or training process. If you encounter a suspicious job posting or anyone asking for application fees, you can verify the posting through the official recruitment contact or report suspected fraud to the Federal Trade Commission. Use our step-by-step checklist below to prepare your application file.
- Audit your certificates and ratings: Confirm your Commercial Pilot Certificate with Multiengine and Instrument ratings (for SIC) or Airline Transport Pilot certificate (for PIC) is current and shows no unresolved limitations.
- Verify 6-month instrument currency: Ensure your logbook shows at least 6 instrument approaches, holding procedures, and course intercepting/tracking within the preceding 6 calendar months in an airplane or approved FSTD under 14 CFR 135.245.
- Compile 5 years of employment and training records: Gather your history from previous operators and training centers so there are no delays during the mandatory PRIA 5-year background review.
- Review Part 135 operational rules: Refresh your knowledge of 14 CFR Part 135 oxygen mask requirements above 25,000 feet MSL (14 CFR 135.89), minimum autopilot altitudes (14 CFR 135.93), and sterile flight deck rules ahead of technical screening.
- Submit directly on official portals: Apply directly through the official careers portal and ensure communications originate from verified company email domains.
How Part 135 charter operations shape pilot interviews
Preparing for an interview at a public charter carrier means understanding both high-altitude turbine operations and customer hospitality. In public charter and commuter operations, flights often operate from private fixed base operator (FBO) facilities where passengers board quickly via tarmac airstairs rather than passing through standard commercial airline gate areas.
Because there is no crowded terminal concourse separating the flight deck from passengers, pilots in these operations represent the flight carrier directly on the ramp and in the cabin. In your interview, be prepared to discuss how you balance professional customer interaction during boarding with strict adherence to General Operations Manual procedures, Minimum Equipment List (MEL) deferrals, and Part 135 safety regulations once preparing for departure.
Practice telling your own stories out loud before your interview date, focusing on real flight experiences where you managed weather diversions, maintenance write-ups under 14 CFR 135.65, or passenger disruptions without rushing a checklist.
Practice example
Imagine you are interviewing for a pilot position at JSX, which operates out of private FBO terminals. Tell me about a time a schedule pressure or customer request conflicted with a flight safety procedure, and how you handled both the procedure and the passenger.
Example answer written by our team. The applicant is invented. While flying a multiengine charter trip out of a private FBO last winter, our passengers arrived planeside 15 minutes before their scheduled departure and asked if we could launch immediately to beat an approaching snow squall. During my walkaround, I noticed light frost adhering to the upper wing surface. Under 14 CFR 135.227, taking off with frost adhering to critical surfaces is prohibited until the aircraft is properly deiced or polished clean. Rather than staying on the flight deck and sending a message through the line crew, I stepped down the airstair and greeted the lead passenger directly in the lounge doorway. I welcomed them aboard, explained that we needed 15 minutes for the FBO deicing truck to spray the wings so we could climb safely through the frontal layer, and invited them to stay warm inside the lounge with coffee while we completed the treatment. Once the clean-aircraft check was complete, we boarded quickly and departed safely.
This answer cites the exact Part 135 clean-aircraft rule while showing the warm, face-to-face communication needed in a private FBO environment. It proves the pilot never compromises safety checklists under time pressure while still treating customers with respect.
Practice this on Fourstripe. Pick your airline and a captain runs the interview out loud: TMAAT, about-you, technical and scenario questions, with real follow-ups. You get a scored report on every answer. 7-day trial, then from $149 a week. Start a practice interview
Frequently asked questions
What regulations govern pilot qualifications for JSX flights?
JSX flights operate under FAA Part 135 regulations and DOT Part 380 public charter rules. Captains and First Officers must meet the mandatory flight crew standards established in 14 CFR 135.243, 135.245, and 14 CFR Part 61.
Do First Officers need an ATP certificate for Part 135 commuter flights?
Under 14 CFR 135.245 and 14 CFR 135.3(b), a pilot serving as Second in Command in a Part 135 commuter operation must hold at least a Commercial Pilot Certificate with appropriate category and class ratings and an instrument rating. Airlines and operators may set additional hiring minimums in their specific job postings.
What are the FAA requirements to serve as Captain in Part 135 commuter flying?
Under 14 CFR 135.243, a Pilot in Command of a turbojet airplane, an airplane with 10 or more passenger seats, or a multiengine airplane in commuter operations must hold an Airline Transport Pilot (ATP) certificate with appropriate category, class, and type ratings. A standard airplane ATP requires at least 1,500 hours of total pilot time under 14 CFR 61.159.
Why do multiengine public charter flights require two pilots?
Under 14 CFR 135.99, no certificate holder may operate an aircraft without a second in command if that aircraft has a passenger seating configuration of 10 seats or more, excluding pilot seats. Aircraft used in these commuter operations require both a Pilot in Command and a Second in Command.
Do legitimate Part 135 operators charge pilot application or training fees?
No, legitimate air carriers and charter operators do not charge application fees or request banking details during hiring. Official hiring guidelines advise applying exclusively through official company portals and communicating only with verified company email domains.
Sources
- JSX Careers Official Page
- eCFR Title 14 Part 135 Operating Requirements: Commuter and On Demand Operations
- eCFR 14 CFR 135.243 Pilot in Command Qualifications
- eCFR 14 CFR 135.244 Operating Experience
- eCFR 14 CFR 135.245 Second in Command Qualifications
- eCFR 14 CFR 135.293 Initial and Recurrent Pilot Testing Requirements
- eCFR 14 CFR 61.159 Aeronautical Experience: Airplane Category Rating
- FAA General Requirements for 14 CFR Part 135 Certification
- ecfr.gov