King Air Pilot: Endorsements, Type Ratings, and Training Rules
Short answer: To act as pilot in command as a King Air pilot under FAA rules, you need an airplane multiengine land rating, an instrument rating for IFR flight, and logbook endorsements for complex, high-performance, and high-altitude pressurized aircraft under 14 CFR 61.31. An FAA type rating is required only if the aircraft has a maximum certificated takeoff weight over 12,500 pounds (14 CFR 1.1) or is modified under a Commuter Category Supplemental Type Certificate. This places the 300 series and select modified 200 series models under the BE-300 or BE-200 type rating.
Which King Air models require a type rating
Under 14 CFR 61.31(a), the FAA requires a pilot in command to hold a type rating for any large aircraft, turbojet-powered airplane, powered-lift, or other aircraft specified through aircraft type certificate procedures.
In 14 CFR 1.1, the FAA defines a large aircraft as an aircraft of more than 12,500 pounds maximum certificated takeoff weight, while a small aircraft is 12,500 pounds or less. Because standard turboprops are not turbojets, this 12,500-pound cutoff is the primary dividing line across the Textron Aviation fleet. The entire King Air 90 series (such as the C90, E90, and F90) and standard models of the 100 and 200 series are certificated at 12,500 pounds or less, meaning they do not require a type rating unless specific modifications apply.
According to FAA Order 8900.1, Volume 5, Chapter 2, Section 19, Figure 5-88, the FAA does not list marketing names in the civil model designation column. To verify whether an airplane requires a type rating, compare the exact model in Block 2 of the Airworthiness Certificate and the serial number against the Flight Standardization Board Report and Figure 5-88.
Transport Canada Civil Aviation (TCCA) categorizes these turbine twins differently. Under TCCA Standard 421.40, the King Air 100, 200, and 300 series are listed under the Aeroplane-High Performance category with a minimum crew of 1 pilot, using individual type designators rather than the FAA weight threshold alone.
- BE-300 (FAA Type Rating): Applies to Textron Aviation civil models 300, 300LW, B300, B300C, and model 300 airplanes with serial numbers FF-1 to FF-19 (prior model designation BE-300F).
- BE-200 (FAA Type Rating): Applies to civil models 200T, 200CT, A200CT, B200C, B200T, B200CT, and B200 as determined by serial number, military equivalent designation, restricted category designation, or any Model 200 series with a Commuter Category Supplemental Type Certificate (STC) applied.
- Standard Small Airplanes (No FAA Type Rating): Airplanes in the 90 series and standard models of the 100 and 200 series have a maximum certificated takeoff weight of 12,500 pounds or less. Because they do not exceed 12,500 pounds and are not turbojets, they do not appear on the FAA type rating designation table and are flown using your category and class rating plus mandatory 14 CFR 61.31 logbook endorsements.
- Transport Canada Designators: Under TCCA Standard 421.40, TCCA assigns BE10 to the King Air 100 and BE20 to all models of the King Air 200. Under Footnote 49, King Air 100 aircraft with a VNE less than 250 KIAS (287.7 mph) do not require an individual type rating and fall under the blanket rating. The designator BE30 covers the Model 300, 300LW, B300 (King Air 350 and 350i), and B300C (King Air 350C, 350iC, 350iCER, 360, and 360ER).
FAA and Transport Canada Type Rating Designations for Textron Aviation Turbine Twins (FAA Order 8900.1 Fig. 5-88 and TCCA Standard 421.40)
| Civil Model Designation | FAA Type Rating | TCCA Type Designator | TCCA Minimum Crew | Notes and Applicability |
|---|---|---|---|---|
| 90 series (including C90, E90, F90) | None listed in Fig. 5-88 | None (blanket rating) | n/a | Certificated at 12,500 pounds or less, requiring no FAA type rating |
| King Air 100 | None listed in Fig. 5-88 | BE10 | 1 | TCCA Footnote 49: VNE less than 250 KIAS (287.7 mph) falls under blanket rating |
| 200, B200, 200T, 200CT, A200CT, B200C, B200T, B200CT | BE-200 (when applicable) | BE20 | 1 | FAA BE-200 applies by serial number per BE-200 FSBR or when Commuter Category STC is applied |
| 300, 300LW, B300, B300C | BE-300 | BE30 | 1 | TCCA BE30 covers marketing names 350, 350i, 350C, 350iC, 350iCER, 360, and 360ER |
| 300 (serial numbers FF-1 to FF-19) | BE-300 | BE30 | 1 | FAA prior model designation BE-300F per Appendix 6 of the BE-300 FSBR |
| 1900, 1900C, 1900D | BE-1900 | BE02 | 1 | FAA equivalent military designation C-12J |
Certificates and ratings needed to fly as pilot in command
Before you add model endorsements or a type rating, 14 CFR 61.3 and 61.31 establish the baseline pilot certificates and ratings required to act as pilot in command (PIC). Under 14 CFR 61.31(c) and (d), to serve as PIC of an aircraft carrying passengers or operated for compensation or hire, you must hold the appropriate category, class, and type rating for that aircraft.
Because these turboprops are twin-engine landplanes, your certificate must carry the Airplane category and Multiengine Land class rating. If flying under Instrument Flight Rules (IFR) or below VFR weather minimums, 14 CFR 61.3(e) requires an instrument rating for that airplane category, class, and type (if required), or an Airline Transport Pilot (ATP) certificate with matching privileges.
When acting as a required flight crewmember on a United States civil aircraft, 14 CFR 61.3(a) and (c) require three items in your physical possession or readily accessible in the aircraft:
- A valid pilot certificate, authorized temporary certificate, or verification document issued under 14 CFR Part 61.
- An official government-issued photo identification, such as a driver's license, passport, military ID, or airport security credential.
- An appropriate, current medical certificate issued under 14 CFR Part 67.
The three mandatory 14 CFR 61.31 logbook endorsements
Regardless of whether your model requires a BE-200 or BE-300 type rating, flying a pressurized twin turboprop triggers three distinct training requirements under 14 CFR 61.31: complex airplane, high-performance airplane, and pressurized high-altitude aircraft.
Under 14 CFR 61.1(b), a complex airplane has retractable landing gear, flaps, and a controllable pitch propeller, or a digital engine and propeller control system such as FADEC. 14 CFR 61.31(e) requires logged ground and flight training from an authorized instructor in a complex airplane or representative simulator, followed by a one-time logbook endorsement.
Under 14 CFR 61.31(f), a high-performance airplane has an engine of more than 200 horsepower. Acting as PIC requires logged ground and flight training from an authorized instructor and a one-time logbook endorsement certifying proficiency. Under 14 CFR 61.31(e)(2) and (f)(2), you are exempt from the complex and high-performance endorsements if you logged PIC time in such an aircraft prior to August 4, 1997, or completed an approved 14 CFR 135.293 competency check.
Under 14 CFR 61.31(g), operating a pressurized aircraft with a service ceiling or maximum operating altitude above 25,000 feet MSL requires specific ground and flight training endorsements from an authorized instructor, unless you qualify for an exemption.
- High-altitude ground subjects (14 CFR 61.31(g)(1)): High-altitude aerodynamics and meteorology, respiration, hypoxia symptoms and causes, duration of consciousness without supplemental oxygen, effects of prolonged oxygen use, causes and effects of gas expansion and bubble formation, preventive measures for decompression sickness, physical phenomena of decompression, and other physiological aspects of high-altitude flight.
- High-altitude flight tasks (14 CFR 61.31(g)(2)): Conducted in a pressurized aircraft or representative simulator, covering normal cruise operations above 25,000 feet MSL, emergency procedures for simulated rapid decompression without actual depressurization, and emergency descent procedures.
- High-altitude exemptions (14 CFR 61.31(g)(3)): The endorsement is not required if you can document serving as PIC in a pressurized aircraft before April 15, 1991, passing a proficiency check before April 15, 1991, completing a U.S. military PIC check, or completing a PIC proficiency check under Part 121, 125, or 135.
How to earn a BE-200 or BE-300 type rating under Part 61
When flying a model that requires a BE-200 or BE-300 type rating, the FAA tests your practical test to Airline Transport Pilot standards, even if you hold a Private or Commercial certificate. Regulations for adding a type rating to a certificate below ATP are in 14 CFR 61.63(d), while adding a type rating to an ATP certificate (or earning one concurrently) is governed by 14 CFR 61.157(b).
Under 14 CFR 61.63(d)(5) and 61.157(b), you do not need to take an additional written knowledge test if you already hold an airplane rating on your certificate, unless applying concurrently for an initial ATP certificate. Training focuses entirely on systems knowledge, cockpit procedures, and practical flight proficiency.
For multiengine airplanes with a single-pilot station, 14 CFR 61.63(f) and 61.157(h) state that the practical test must be performed in the multi-seat version, or in the single-seat version if the Examiner can observe the applicant and no multi-seat version exists.
Under 14 CFR 61.157(e)(2), the practical test for an airplane multiengine rating or type rating covers 8 areas of operation:
- Prerequisites: Hold or concurrently obtain an instrument rating (14 CFR 61.63(d)(1)).
- Training: Receive and log ground and flight training from an authorized instructor on the applicable areas of operation.
- Instructor endorsement: Obtain an endorsement certifying aeronautical knowledge and flight proficiency at the ATP level.
- Practical test: Pass the ATP-level practical test in actual or simulated instrument conditions covering all 8 areas of operation: preflight preparation, preflight procedures, takeoffs and landings, in-flight maneuvers, stall prevention, instrument procedures, emergency operations, and postflight procedures.
- Air carrier exception (14 CFR 61.63(d)(6) and 61.157(c)): Pilot employees of Part 121, Part 135, or Part 91K operators satisfy training endorsements via completion of an approved training program. Under 14 CFR 61.157(f), passing both a 135.293 competency check and a 135.297 PIC instrument proficiency check satisfies flight proficiency requirements.
Second-in-command qualifications and the SIC type rating
A pilot may log flight time as second in command (SIC) in aircraft certificated for two pilots or in Part 135 operations requiring a second pilot under 14 CFR 135.101. Flying under an approved Part 135.99(c) SIC professional development program also qualifies as pilot time under 14 CFR 61.1(b).
To serve as SIC in operations requiring two pilots, 14 CFR 61.55(a) requires at least a private pilot certificate with appropriate category and class ratings, an instrument rating for IFR, and an aircraft type rating unless flights remain entirely within domestic United States airspace.
Under 14 CFR 61.55(b), you must complete familiarization and flight currency within the preceding 12 calendar months (with a one-month grace window under 61.55(c)). For flights outside U.S. airspace, you can obtain an SIC Privileges Only type rating under 14 CFR 61.55(d) or (e) without taking a practical test.
- Familiarization ground review (14 CFR 61.55(b)(1)): Operational procedures for powerplant, equipment, and systems, performance specifications and limitations, normal, abnormal, and emergency procedures, flight manual, and placards and markings.
- Flight training currency (14 CFR 61.55(b)(2)): Perform and log three takeoffs and three landings to a full stop as sole manipulator of the controls, engine-out procedures while executing PIC duties, and crew resource management training within the last 12 calendar months.
- Simulator rule for initial SIC (14 CFR 61.55(j)): If initial SIC training occurs entirely in a flight simulator, complete at least one takeoff and one landing in the aircraft, unless exempt via a Part 91K, 121, 125, or 135 check.
- Application steps for SIC type rating (14 CFR 61.55(d)): Have an authorized instructor or management official sign logbook records, provide the 61.55(d)(2) endorsement, sign the recommendation on FAA Form 8710-1, and present records in person to a Flight Standards office or Examiner.
Special operations: NVG endorsements and ferry authorizations
Special flight profiles trigger two additional 14 CFR 61.31 provisions: Night Vision Goggle (NVG) endorsements and ferry flight authorizations.
Under 14 CFR 61.1(b), an NVG operation occurs from 1 hour after sunset to 1 hour before sunrise where the pilot maintains visual surface reference using night vision goggles in an approved aircraft. Acting as PIC requires ground training on 5 subject areas and flight training on 4 task areas under 14 CFR 61.31(k), unless exempt through military, Part 135, or law enforcement checks (with at least 20 hours PIC in NVG operations for law enforcement).
If you need to reposition a model requiring a type rating before completing your checkride, 14 CFR 61.31(b) allows the FAA to issue a 60-day authorization in lieu of a type rating, renewable for an additional 60 days if necessary.
- The flight must be a ferry, training, test, or practical test flight.
- The flight must remain entirely within the United States.
- The flight cannot involve compensation or hire, except payment solely for aircraft use during training or testing.
- The flight may carry only flight crewmembers considered essential.
Practice example
Walk me through when a King Air requires an FAA type rating versus logbook endorsements, and explain what training you needed to legally act as PIC above FL250.
Example answer, written by us. It is not a real applicant's story. Under 14 CFR 61.31(a) and 14 CFR 1.1, the FAA requires a type rating to act as pilot in command of any large aircraft with a maximum certificated takeoff weight of more than 12,500 pounds, or when specified by type certificate procedures. For the King Air 300 and B300 series, that means holding a BE-300 type rating. For the 200 series, standard models at or below 12,500 pounds do not require a type rating, though a BE-200 type rating is required for specific serial numbers and models modified with a Commuter Category STC. For models at or below 12,500 pounds, I needed my Airplane Multiengine Land and Instrument ratings plus the complex and high-performance endorsements under 14 CFR 61.31(e) and (f). Because the service ceiling is above 25,000 feet MSL, I also completed the 14 CFR 61.31(g) high-altitude ground and flight training endorsements covering hypoxia, time of useful consciousness, simulated rapid decompression, and emergency descents.
This answer cites the exact regulatory weight cutoff in 14 CFR 1.1 and 61.31(a), distinguishes between the BE-300 and BE-200 type rating rules, and names the specific ground and flight training items required by 14 CFR 61.31(g).
Practice this on Fourstripe. Pick your airline and a captain runs the interview out loud: TMAAT, about-you, technical and scenario questions, with real follow-ups. You get a scored report on every answer. 7-day trial, then from $149 a week. Start a practice interview
Frequently asked questions
Do you need a type rating to fly a King Air?
Under 14 CFR 61.31(a) and 14 CFR 1.1, you only need an FAA type rating if the specific airplane weighs more than 12,500 pounds maximum certificated takeoff weight or is required by type certificate procedures. According to FAA Order 8900.1 Figure 5-88, the 300, 300LW, B300, and B300C require a BE-300 type rating, while specific 200 series models with commuter category modifications require a BE-200 type rating.
What endorsements do you need for a King Air under 12,500 pounds?
For models that do not require a type rating, acting as pilot in command requires an airplane multiengine land rating plus three logbook endorsements under 14 CFR 61.31: complex airplane (61.31(e)), high-performance airplane for engines exceeding 200 horsepower (61.31(f)), and pressurized aircraft operating above 25,000 feet MSL (61.31(g)).
What does the 14 CFR 61.31(g) high-altitude endorsement cover?
Under 14 CFR 61.31(g), you must complete ground training on subjects including hypoxia, duration of consciousness, and decompression, plus flight training in a pressurized aircraft or simulator covering cruise above 25,000 feet MSL, simulated rapid decompression, and emergency descents. An exemption applies if you completed an official military or Part 121, 125, or 135 PIC check in a pressurized aircraft.
Do I have to take a written knowledge test for a BE-300 type rating?
No, if you add a BE-300 type rating to an existing pilot certificate that already has an airplane rating, 14 CFR 61.63(d)(5) states that you do not need to take an additional written knowledge test. However, you must pass the practical test at the Airline Transport Pilot certification level in actual or simulated instrument conditions.
How do I qualify as second in command (SIC) in a King Air?
Under 14 CFR 61.55, when an operation or aircraft requires an SIC, you must hold at least a private pilot certificate with an airplane multiengine land rating, an instrument rating for IFR, and complete annual familiarization training plus three takeoffs and full-stop landings, engine-out procedures, and CRM training within the preceding 12 calendar months. International flights outside U.S. airspace also require an SIC pilot type rating.
Sources
- eCFR: 14 CFR 61.31 Type Rating Requirements, Additional Training, and Authorization Requirements
- eCFR: 14 CFR 1.1 General Definitions
- eCFR: 14 CFR Part 61 Certification: Pilots, Flight Instructors, and Ground Instructors
- eCFR: 14 CFR 61.63 Additional Aircraft Ratings
- eCFR: 14 CFR 61.157 Flight Proficiency
- eCFR: 14 CFR 61.55 Second-in-Command Qualifications
- eCFR: 14 CFR Part 135 Operating Requirements: Commuter and On Demand Operations
- FAA Order 8900.1 Figure 5-88: Pilot Certificate Aircraft Type Designations
- Transport Canada Standard 421.40: Aircraft Type Designators for Individual Type Ratings