MDA vs DA: Precision vs Non-Precision Minima

Short answer: Decision Altitude (DA) is a specified MSL altitude on vertically guided approaches (such as ILS, GLS, LPV, and LNAV/VNAV) where you must start an immediate missed approach without visual references. Per FAA AIM 5-4-5, obstacle clearance allows a momentary dip below DA during that transition. Minimum Descent Altitude (MDA) is the lowest MSL altitude on nonprecision approaches (such as VOR, LOC, LP, and LNAV) and circling procedures. You cannot descend below the MDA without meeting the visual landing requirements of 14 CFR 91.175(c), and you must initiate any missed approach at or above the MDA.

Last checked November 6, 2026.

MDA vs DA side-by-side comparison

When an airline interview panel or simulator evaluator asks you to compare MDA and DA, they are testing whether you know how vertical guidance changes obstacle protection, stepdown fixes, and missed approach execution. Both MDA and DA are referenced to mean sea level (MSL) and read on a barometric altimeter.

The difference is how the procedure is designed under U.S. Standard for Terminal Instrument Procedures (TERPS) criteria and what you must do when the aircraft reaches minimums.

Feature Decision Altitude (DA) Decision Height (DH) Minimum Descent Altitude (MDA)
Altitude reference Mean Sea Level (MSL) on barometric altimeter Threshold elevation (AGL). Radio Altimeter for CAT II/III Mean Sea Level (MSL) on barometric altimeter
Approach types Precision (ILS, PAR, GLS) and APV (LPV, LNAV/VNAV, LDA with glideslope) Category II and III ILS (also used in regulatory text for CAT I / PAR) Nonprecision (VOR, NDB, LOC, LNAV, LP, ASR, SDF), Circling, and Side-step
Vertical guidance Required (electronic glideslope or glidepath) Required (electronic glideslope) None (lateral guidance only. VDA or +V is advisory only)
Action at minimums without visual reference Initiate an immediate missed approach at DA Initiate an immediate missed approach at DH Maintain at or above MDA until reaching the Missed Approach Point (MAP)
Dipping below minimums on go-around Permitted. Obstacle clearance allows a momentary descent below DA during transition Permitted within Category II/III certification limits Prohibited. Missed approach obstacle protection requires initiating at or above MDA
Final Approach Segment (FAS) stepdown fixes Do not apply when following vertical guidance to a DA Do not apply Mandatory. Must comply with all stepdown fix altitudes
Visual Descent Point (VDP) Does not apply Does not apply Applies to straight-in nonprecision approaches (such as LP and LNAV)
Missed Approach Point (MAP) location The point on the glidepath where the aircraft reaches the DA The point on the glidepath where the aircraft reaches the DH A published fix, NAVAID, waypoint, or elapsed time from the FAF

What is Decision Altitude (DA) and Decision Height (DH)

According to the FAA Pilot/Controller Glossary, Decision Altitude (DA) is a specified altitude in mean sea level (MSL) on an instrument approach procedure with vertical guidance where you must decide whether to continue the approach or initiate an immediate missed approach if you do not see the required visual references. Under FAA AIM 5-4-5, the FAA replaced the older charting term Decision Height (DH) with DA on standard vertically guided charts to match the international convention where altitudes relate to MSL and heights relate to AGL.

Decision Height (DH) is referenced to the runway threshold elevation. Category II and Category III ILS minima are expressed as a DH rather than a DA because the minima are assessed using a radio altimeter instead of a barometric altimeter. Per FAA AIM 1-1-9, the lowest authorized standard Category I ILS minimum is a 200-foot height and RVR 2,400 feet (or RVR 1,800 feet with touchdown zone and centerline lighting, or with an operative flight director, autopilot, or head-up display to DA). Category II ILS approaches go down to a DH of 100 feet and RVR 1,200 feet (or RVR 1,000 feet with autoland or HUD to touchdown).

Two groups of approaches publish a DA. The first is Precision Approaches (PA), which provide course and glidepath deviation information meeting ICAO Annex 10 precision standards: Instrument Landing System (ILS), Precision Approach Radar (PAR), and GBAS Landing System (GLS). The second group is Approaches with Vertical Guidance (APV), which provide course and glidepath deviation information without meeting ICAO Annex 10 precision standards: Localizer Performance with Vertical Guidance (LPV), LNAV/VNAV, Baro-VNAV, and Localizer Type Directional Aid (LDA) with glidepath.

Because you fly a continuous descent profile down an electronic glidepath to a DA, aircraft momentum will carry you slightly downward as you pitch up and add thrust for a go-around. Obstacle clearance is provided to allow a momentary descent below DA while transitioning from the final approach to the missed approach.

What is Minimum Descent Altitude (MDA)

Minimum Descent Altitude (MDA) is the lowest MSL altitude to which descent is authorized on final approach or during circle-to-land maneuvering in execution of a standard instrument approach procedure where no electronic glideslope is provided. You will fly to an MDA on Nonprecision Approaches (NPA) that provide lateral course deviation information only, including VOR, NDB, Localizer (LOC), Simplified Directional Facility (SDF), Airport Surveillance Radar (ASR), RNAV LNAV, and WAAS Localizer Performance (LP). You also fly to an MDA on every circling approach and every side-step maneuver.

Unlike a DA, an MDA is a hard altitude floor. Under 14 CFR 91.175(c) as cited in FAA AIM 5-4-7, no pilot may operate an aircraft below the authorized MDA or continue an approach below the authorized DA/DH unless the aircraft is continuously in a position to land on the intended runway at a normal descent rate using normal maneuvers. For Part 121 or Part 135 operations, that descent rate must also allow touchdown within the touchdown zone of the intended runway.

Per FAA AIM 5-4-21, missed approach obstacle protection is predicated on the missed approach being initiated at the DA/DH, or at the missed approach point (MAP) and not lower than the MDA, assuming a minimum climb gradient of at least 200 feet per nautical mile (or 400 feet per nautical mile for helicopters). If you dip below the MDA without the required visual references and initiate a missed approach from below the MDA, obstacle clearance is not assured.

  • LNAV obstacle clearance: A horizontal line is drawn at the controlling obstacle height and 250 feet is added for Required Obstacle Clearance (ROC), then rounded up to the next higher 20-foot increment.
  • Circling MDA obstacle clearance: Provides 300 feet of obstacle clearance within the circling approach protected area and is never lower than the straight-in LNAV MDA.
  • LP (Localizer Performance) minima: Uses WAAS angular lateral sensitivity similar to a localizer, but has no approved vertical guidance and is always published as an MDA. Even when WAAS avionics generate GNSS-based advisory vertical guidance on an LP approach, the barometric altimeter remains the primary altitude reference.
  • Vertical Descent Angle (VDA): Published on most nonprecision charts to aid in flying a stabilized constant-rate descent, but a VDA is strictly advisory, does not guarantee obstacle protection below the MDA, and does not turn the procedure into an APV.

Why an LNAV/VNAV DA can be higher than an LNAV or Circling MDA

A classic airline technical interview question asks you to explain how a vertically guided LNAV/VNAV Decision Altitude can be charted higher than the nonprecision LNAV MDA or Circling MDA on the exact same RNAV (GPS) approach plate.

FAA AIM Figure 5-4-12 and Figure 5-4-13 give a real charting example of this exact scenario: on that sample chart, the LPV DA is 558 feet MSL (250 feet HAT), the LNAV/VNAV DA is 1,572 feet MSL (1,264 feet HAT), the straight-in LNAV MDA is 1,180 feet MSL (872 feet HAT), and the Circling MDA is 1,180 feet MSL (870 feet HAA). By our calculation from Figure 5-4-12, the vertically guided LNAV/VNAV DA on that procedure is 392 feet higher than both the LNAV MDA and the Circling MDA, and 1,014 feet higher than the LPV DA.

The reason comes down to how TERPS evaluates obstacles for a sloping obstacle clearance surface (OCS) versus a flat horizontal surface. For LNAV (no vertical guidance), procedure designers draw a horizontal line at the controlling obstacle height, add 250 feet of ROC, and round up to the next 20-foot increment. For LNAV/VNAV (vertical guidance), designers draw a horizontal line from the obstacle height until it intersects the sloping obstacle clearance surface (OCS), and from that intersection they draw a vertical line straight up to the glidepath to establish the DA. This places the offending obstacle in front of the LNAV/VNAV DA so that you can see and avoid it, and allows for the momentary dip below DA during a go-around. When a prominent obstacle sits far out on final approach, projecting it horizontally to the OCS and vertically up to the glidepath pushes the LNAV/VNAV DA higher than the flat LNAV or Circling MDA.

How to brief and fly stepdown fixes, VDPs, and the MAP

During a simulator evaluation, check airmen watch how you manage altitude constraints between the Final Approach Fix (FAF) and the runway. The rules change depending on whether you brief a DA or an MDA.

Stepdown fixes in the Final Approach Segment (FAS): Altitude restrictions depicted at stepdown fixes within the final approach segment apply only when you are flying a nonprecision approach to a straight-in or circling line of minima identified as an MDA(H). These fixes are often annotated with 'LOC only' or 'LNAV only.' Stepdown fix altitude restrictions inside the final approach segment do not apply when you are flying a Precision Approach (ILS) or APV (LPV, LNAV/VNAV) to a DA(H), because obstacle clearance on vertically guided approaches is based on following the vertical glidepath. However, stepdown fix altitude restrictions outside the final approach segment (in the initial or intermediate segments) are mandatory for all aircraft regardless of whether you are flying to an MDA or a DA.

Visual Descent Point (VDP): Identified by a 'V' symbol on the profile view, the VDP is a defined point on the final approach course of a nonprecision straight-in approach from which you can begin a stabilized visual descent from the MDA to the runway touchdown point. You should not descend below the MDA prior to reaching the VDP, and VDPs apply only to aircraft using LP or LNAV (MDA) minima, never to LPV or LNAV/VNAV (DA) minimums.

Missed Approach Point (MAP) and early go-arounds: On a vertically guided approach, the MAP is the point on the glidepath where the aircraft reaches the DA/DH. On a non-vertically guided or circling procedure, the MAP is a fix, NAVAID, waypoint, or a specified time from the FAF. If you initiate a missed approach early (prior to reaching the MAP), unless otherwise cleared by ATC, you must continue along the published final approach course at or above the MDA or DA/DH to the published MAP or runway threshold waypoint before executing any turning maneuver.

Visual segment obstacles: There is no implicit obstacle protection from either the MDA or the DA to the touchdown point. Once below the MDA or DA, it is your responsibility to visually acquire and avoid obstacles during the transition to landing. If an obstacle penetrates the visual surface enough to disallow a published VDA, the profile view will display the note 'Visual Segment - Obstacles.'

Pre-approach briefing checklist (written by our team from FAA AIM 5-4-5 and 5-4-21):

  • State the active line of minima (GLS, ILS, LPV, LNAV/VNAV, LP, LNAV, or Circling) and announce whether it is a DA, DH, or MDA.
  • Verify the altimeter setting source. Remember that Baro-VNAV (LNAV/VNAV) requires the local altimeter setting only unless using WAAS electronic vertical guidance.
  • Check temperature limits: verify the Baro-VNAV temperature range box and check for the Cold Temperature Airport (CTA) snowflake icon.
  • Brief all stepdown fixes outside the FAF (mandatory for everyone) and state whether stepdown fixes inside the FAF apply (mandatory for MDA, not applicable for DA).
  • Identify the MAP (reach DA on glidepath vs named waypoint, NAVAID, or timing from FAF) and the VDP distance if flying an MDA.
  • Brief the initial missed approach climb gradient (standard 200 ft/NM fixed-wing or higher charted gradient) and remind the crew that any early missed approach requires tracking final at or above MDA/DA to the MAP before turning.

Special scenarios: inoperative glideslope, side-step, circling, and EFVS

Evaluators frequently introduce equipment failures or ATC clearance changes on arrival to see if you recognize when a DA approach converts into an MDA approach. Here is how FAA procedures govern each case.

Inoperative ILS glideslope: If the localizer fails, an ILS approach is not authorized. When the glideslope fails, the ILS reverts to a nonprecision localizer (LOC) approach. You must brief the LOC MDA, comply with all 'LOC only' final segment stepdown fixes, and identify the nonprecision MAP.

Side-step maneuvers: ATC may clear you for an approach to one runway followed by a straight-in landing on an adjacent parallel runway separated by 1,200 feet or less (for example, 'Cleared ILS Runway 7 Left approach, side-step to Runway 7 Right'). Per FAA AIM 5-4-19, side-step minima are always flown to an MDA regardless of the approach authorized, and you must comply with minimum altitudes at stepdown fixes even after initiating the side-step maneuver.

Circling restrictions on vertically guided charts: Every circling line of minima is an MDA. Furthermore, FAA AIM 5-4-20 states that circling from a GLS approach, an ILS approach without a localizer line of minima, or an RNAV (GPS) approach without an LNAV line of minima is prohibited. If you lose visual reference while circling to land, you must make an initial climbing turn toward the landing runway and continue the turn until established on the prescribed missed approach course.

Enhanced Flight Vision Systems (EFVS): Under FAA AIM 5-4-22 and 14 CFR 91.176, EFVS operations to touchdown and rollout (Paragraph 91.176(a)) are permitted only on approaches published with a DA or DH (precision or APV) and are prohibited on circling approaches. EFVS operations to 100 feet above the touchdown zone elevation (Paragraph 91.176(b)) may be conducted on straight-in approaches published with either a DA/DH or an MDA, and require identifying the visual references using natural vision to continue below 100 feet above the TDZE.

When you are preparing for your technical oral, pair this review with our guides on holding pattern speeds and entries, alternates and 1-2-3 rule weather minimums, and cold temperature altitude corrections.

Practice question

Practice interview question (LNAV/VNAV DA vs LNAV MDA): You are briefing the RNAV (GPS) Runway 21 approach. There is a stepdown fix inside the Final Approach Fix, and you notice the LNAV/VNAV DA is 390 feet higher than the LNAV MDA. How do you explain why the DA is higher to the Captain, and how does your choice of LPV/LNAV/VNAV versus LNAV change how you fly that stepdown fix and the missed approach?

Example answer, written by us. It is not a real applicant's story. First, I would explain that the LNAV/VNAV DA is higher than the LNAV MDA because of how TERPS calculates obstacle clearance for a vertically guided path versus a flat nonprecision floor. For LNAV, designers draw a flat line at the controlling obstacle and add 250 feet of Required Obstacle Clearance. For LNAV/VNAV, they draw a horizontal line from the obstacle out to the sloping obstacle clearance surface and then go straight up to the glidepath to set the DA. That puts the obstacle in front of the DA and protects us for a momentary dip below DA during a go-around, which can push the LNAV/VNAV DA higher than the LNAV MDA. Second, if we fly to the LPV or LNAV/VNAV DA, the stepdown fix inside the Final Approach Fix does not apply to us because our obstacle clearance is provided by tracking the electronic glidepath, and our Missed Approach Point is the point where we reach the DA on the glidepath. If we fly to the LNAV MDA instead, that final segment stepdown fix is mandatory, we must treat the MDA as a hard floor that we cannot dip below without meeting 14 CFR 91.175 visual requirements, we will not descend below MDA prior to the VDP, and if we go missed early, we will climb at or above the MDA straight ahead to the missed approach waypoint before making any turns.

This answer hits every technical point from FAA AIM 5-4-5 and 5-4-21 in logical order: it explains the horizontal-to-OCS-to-glidepath geometry for LNAV/VNAV vs the 250-foot ROC for LNAV, distinguishes FAS stepdown fix applicability, contrasts dipping below DA with the hard floor of MDA, and states the early missed approach turn restriction.

Practice this on Fourstripe. A panel captain asks TMAAT, about-you, technical and scenario questions out loud, follows up on what you said, and scores every answer. 7-day trial, then from $149 a week. Start a practice interview

Fourstripe is not affiliated with any airline.

Frequently asked questions

Can you dip below MDA or DA during a missed approach?

You can dip momentarily below a DA, because FAA AIM 5-4-5 states that obstacle clearance is provided to allow a momentary descent below DA while transitioning from the final approach to the missed approach. You cannot dip below an MDA without visual references. Per FAA AIM 5-4-21, missed approach obstacle protection is predicated on initiating the missed approach at the MAP and not lower than the MDA.

Do final approach segment stepdown fixes apply when flying to a DA?

No. Stepdown fix altitude restrictions within the final approach segment apply only when flying a nonprecision approach to an MDA(H), though stepdown fix restrictions outside the final approach segment (initial or intermediate segments) must be complied with on all approaches.

Why is an LNAV/VNAV DA sometimes higher than the LNAV or Circling MDA on the same chart?

LNAV/VNAV obstacle evaluation draws a horizontal line from the obstacle to the sloping obstacle clearance surface (OCS) and then a vertical line up to the glidepath to set the DA, placing the offending obstacle in front of the DA. This geometry can push the LNAV/VNAV DA higher than the flat LNAV MDA (which adds 250 feet of obstacle clearance) or Circling MDA (which provides 300 feet of obstacle clearance).

What is the difference between Decision Altitude (DA) and Decision Height (DH)?

According to the FAA Pilot/Controller Glossary, Decision Altitude (DA) is referenced to mean sea level (MSL) and read on a barometric altimeter, while Decision Height (DH) is referenced to the runway threshold elevation. Category II and III ILS minima are published as a DH because they are assessed using a radio altimeter rather than a barometric altimeter.

Does a Visual Descent Point (VDP) apply when flying to an LPV or LNAV/VNAV DA?

No. Visual Descent Points (VDPs) apply only to aircraft using nonprecision LP or LNAV (MDA) minima, and do not apply to LPV or LNAV/VNAV (DA) minimums.

What happens to your minimums if you are cleared for an ILS approach with a side-step maneuver?

Per FAA AIM 5-4-19, side-step maneuvers to an adjacent parallel runway (separated by 1,200 feet or less) are always flown to a Minimum Descent Altitude (MDA) regardless of the approach authorized, and you must comply with all stepdown fix minimum altitudes even after starting the side-step.

Sources

Related guides