Omni International Airlines: Part 121 Pilot Qualifications and Regulatory Guide

Short answer: Pilots searching for omni international airlines are preparing for opportunities with Omni Air International under FAA Part 121 standards. Under 14 CFR 121.436 (up to date as of November 9, 2026), second-in-command pilots must hold an Airline Transport Pilot certificate and an appropriate aircraft type rating, while pilots in command must also hold an unrestricted ATP certificate and 1,000 hours of qualifying air carrier or military PIC experience. Before you begin service, an air carrier must evaluate your FAA, employer, and driving records through the Pilot Records Database under 14 CFR Part 111.

Name clarification and regulatory framework

If you are researching pilot careers or federal regulations under the search term omni international airlines, the carrier name referenced in Federal Aviation Administration dockets is Omni Air International. For pilots aiming to fly for a commercial operator under 14 CFR Part 121, crewmember certification and qualification are governed by strict federal standards.

Every Part 121 certificate holder and pilot applicant is governed by the crewmember qualification rules in 14 CFR Part 121 Subpart O and the background screening mandates in 14 CFR Part 111. Understanding these federal standards helps you verify that your logbooks, certificates, and federal records are ready before you sit down with an interview panel.

Part 121 pilot certification and flight time minimums

When preparing to fly for an air carrier such as Omni Air International, you must meet the federal qualification baseline in 14 CFR 121.436. For a second in command (SIC), 14 CFR 121.436(b) requires you to hold an Airline Transport Pilot (ATP) certificate and an appropriate aircraft type rating for the aircraft being flown. A second-in-command type rating obtained under 14 CFR 61.55 does not satisfy this requirement.

Per FAA Pilot Training guidance (updated June 8, 2026), applicants for an ATP certificate with an airplane category multiengine class rating or an ATP certificate issued concurrently with an airplane type rating must complete the ATP Certification Training Program (ATP CTP), governed by Advisory Circular 61-138. The FAA also authorizes institutions of higher education under AC 61-139 to certify graduates of specific aviation degree programs for a restricted privileges ATP (R-ATP) certificate with reduced aeronautical experience, allowing a pilot with fewer than 1,500 hours to serve as a co-pilot until reaching 1,500 hours.

However, 14 CFR 121.432(a) and 121.436(a) set a stricter rule for long-range crews. If you serve as second in command in a flag or supplemental operation that requires three or more pilots, you must be fully qualified to act as pilot in command of that operation (except for operating experience under 121.434 and specific mentoring ground training). That means you must hold an ATP certificate not subject to the restricted privileges limitations in 14 CFR 61.167.

To serve as pilot in command in Part 121 operations, 14 CFR 121.436(a)(3) requires 1,000 hours of specific air carrier experience. Under 14 CFR 121.436(c), you may credit up to 500 hours of military flight time toward that 1,000-hour requirement if you logged it as PIC in a multiengine, turbine-powered, fixed-wing airplane or powered-lift aircraft in an operation requiring more than one pilot.

FAA Part 121 Pilot Certification and Experience Requirements (14 CFR 121.432 and 121.436)

Duty Position ATP Certificate Standard Type Rating Requirement Part 121 Specific Experience
Second in Command (2-pilot crew) ATP certificate (R-ATP permitted for co-pilot until reaching 1,500 hours) Appropriate aircraft type rating (61.55 SIC rating does not qualify) Must complete operations familiarization and IOE under 121.434 and 121.435
Second in Command (Flag or supplemental operation requiring 3 or more pilots) Unrestricted ATP certificate (not subject to 61.167 limitations) Appropriate aircraft type rating Must be fully qualified to act as PIC (except 121.434 operating experience and mentoring ground training)
Pilot in Command (PIC) Unrestricted ATP certificate (not subject to 61.167 limitations) Appropriate aircraft type rating 1,000 hours in qualifying Part 121 SIC, Part 91.1053(a)(2)(i) PIC, or Part 135.243(a)(1) / 135.4(a)(2)(ii)(A) PIC (up to 500 hours military PIC credit allowed)

Operations familiarization, IOE, and 100-hour consolidation

Once hired by a Part 121 operator, you must complete a sequence of training and line qualification events under 14 CFR Part 121 Subpart O before serving as a required flight crewmember.

First, under 14 CFR 121.435, any newly hired pilot who began basic indoctrination ground training on or after April 27, 2022, must complete operations familiarization before beginning operating experience. You must fly at least 2 operating cycles conducted by the certificate holder under Part 121 rules while occupying the flight deck observer seat with access to and use of an operational headset. An operating cycle is a complete flight segment consisting of a takeoff, climb, enroute portion, descent, and landing.

Second, under 14 CFR 121.434, you must complete initial or transition operating experience (IOE) in flight during Part 121 operations under the supervision of a qualified check pilot. If you completed your preflight visual inspection during your proficiency check by approved pictorial means, 14 CFR 121.434(b)(3) requires you to demonstrate proficiency to a check pilot on at least one complete preflight visual inspection of the interior and exterior of a static airplane before completing operating experience.

For Group II airplanes (which include turbojet-powered transport airplanes), 14 CFR 121.434(c)(3) sets the minimum operating experience hours and cycles. While 14 CFR 121.434(f) allows some crewmembers to reduce flight hour requirements by up to 50 percent by substituting one additional takeoff and landing for each hour of flight, pilots in Group II initial training and second-in-command pilots in Group II transition training are explicitly excluded from this reduction.

Third, under 14 CFR 121.434(g), both PIC and SIC crewmembers must acquire at least 100 hours of line operating flight time for consolidation of knowledge and skills (which includes your IOE hours) within 120 days after satisfactorily completing your type rating practical test or a 14 CFR 121.441 proficiency check. Under 14 CFR 121.434(h)(4), the certificate holder may extend the 120-day period to no more than 150 days if you meet all other Subpart O requirements and complete refresher training or a supervised line observation flight with a check pilot on or before the 120th day.

Operating Experience and Consolidation Standards for Pilots (14 CFR 121.434 and 121.435)

Qualification Stage Group I Reciprocating Group I Turbopropeller Group II Airplanes Cycle & Time Rules
Operations Familiarization (121.435) Applies to all new hires Applies to all new hires Applies to all new hires At least 2 operating cycles in flight deck observer seat with headset before IOE
Initial Training Operating Experience (121.434) 15 hours 20 hours 25 hours (no takeoff/landing reduction allowed) Must include at least 4 operating cycles (at least 2 as pilot flying)
Transition Training Operating Experience (121.434) 10 hours 12 hours 25 hours for PIC. 15 hours for SIC (no reduction for SIC) Must include at least 4 operating cycles (at least 2 as pilot flying)
Consolidation of Knowledge and Skills (121.434(g)) 100 hours (includes IOE) 100 hours (includes IOE) 100 hours (includes IOE) Within 120 days of practical test or 121.441 check (extendable up to 150 days with check/refresher)

Pilot Records Database (PRD) screening and preparation checklist

Under 14 CFR Part 111, the Pilot Records Improvement Act (PRIA) ceased to be an available alternative on September 9, 2024. Every Part 121 operator must use the FAA Pilot Records Database (PRD) to evaluate your background before permitting you to begin service as a pilot. Under 14 CFR 111.20(b), no person may use the PRD for any purpose other than to inform a hiring decision concerning a pilot or to report required information.

Under 14 CFR 111.105 and 111.135, the reviewing entity must evaluate your current pilot and medical certificates, any failed practical tests for a certificate or type rating under Part 61, non-overturned FAA enforcement findings, aviation accidents or incidents where you acted as PIC or SIC, and DOT drug and alcohol records (verified positive drug tests, alcohol misuse violations including confirmed results of 0.04 or greater, and testing refusals). The carrier also evaluates training, qualification, proficiency, final disciplinary action, and final separation from employment records submitted by previous reporting entities under Subpart C, along with your National Driver Register (NDR) motor vehicle driving history.

Use our pre-interview checklist below to complete your required PRD actions under 14 CFR Part 111 Subpart D before your interview.

  • Apply for electronic PRD access at least 7 days early: Under 14 CFR 111.305(c), you must submit your application for electronic database access at least 7 days before you seek to access the PRD, using your full name as it appears on your pilot certificate, your FAA certificate number, mailing address, phone number, and email.
  • Audit your FAA and employer records: Under 14 CFR 111.315, review your comprehensive PRD record, including check pilot comments on training events (111.225), any final disciplinary actions (111.230), and separation records (111.235). Verify that no protected Voluntary Safety Reporting Program records (111.245) or flight/duty/rest records (111.225(b)) were improperly uploaded.
  • Report any inaccuracies immediately: Under 14 CFR 111.320 and 111.250, if you spot an error, report it through the PRD. A reporting entity must correct a confirmed inaccuracy within 10 days or initiate a dispute investigation within 30 days.
  • Update your 5-year employment history and grant consent: Under 14 CFR 111.310(a) and (b), before an airline can pull your PRD file, you must provide written consent in the database and affirm that your employment history for the preceding 5 years is accurate and complete.
  • Sign your NDR driving record consent and request copies: Under 14 CFR 111.110 and 111.310(c), sign the separate written consent allowing the carrier to query the National Driver Register. If you want to see the state driving records the airline receives, submit a request under 14 CFR 111.120(c) and the operator must provide copies to you within 30 days.

Line operating limitations and pairing requirements

Technical interviews at Part 121 carriers test your knowledge of line operating limitations, pairing rules, and currency windows. Under 14 CFR 121.438(b), no person may conduct Part 121 operations unless either the PIC or the SIC has at least 75 hours of line operating flight time in that type airplane.

Furthermore, under 14 CFR 121.438(a), if the SIC has fewer than 100 hours of flight time as SIC in Part 121 operations in the type airplane being flown, and the PIC is not an appropriately qualified check pilot, the PIC must make all takeoffs and landings at designated special airports and whenever any of the following conditions exist:

  • Prevailing visibility in the latest weather report for the airport is at or below 3/4 mile.
  • Runway visual range (RVR) for the runway to be used is at or below 4,000 feet.
  • The runway has water, snow, slush, or similar conditions that may adversely affect airplane performance.
  • Braking action on the runway is reported to be less than good.
  • Crosswind component for the runway is in excess of 15 knots.
  • Windshear is reported in the vicinity of the airport, or any other condition in which the PIC determines it is prudent to exercise the PIC's prerogative.

Recency of experience and recurrent check requirements

Under 14 CFR 121.439, to maintain recency of experience, every required pilot must make at least 3 takeoffs and landings within the preceding 90 days in the airplane type (or an approved Level B or higher full flight simulator). If your 90-day recency lapses, 14 CFR 121.439(b) requires you to re-establish recency under the supervision of a check pilot by performing at least 3 takeoffs and landings that include at least one takeoff with a simulated failure of the most critical powerplant, at least one landing from an ILS approach to the lowest ILS minimum authorized for the certificate holder, and at least one landing to a full stop.

For ongoing qualification under 14 CFR 121.433(c), 121.440, and 121.441, a PIC must pass a line check within the preceding 12 calendar months (over a typical route/airway for domestic and flag operations, or over a Federal, foreign, or advisory route for supplemental operations) and complete a proficiency check within the preceding 12 calendar months plus either a proficiency check or an approved FFS training course within the preceding 6 calendar months. All other pilots must complete a proficiency check or line-oriented flight training course within the preceding 24 calendar months, and a proficiency check or FFS course within the preceding 12 calendar months.

Finally, under 14 CFR 121.445, to serve as PIC into a designated special qualification airport, either the PIC or SIC must have made an entry (including takeoff and landing) into that airport within the preceding 12 calendar months, or the PIC must have qualified by acceptable pictorial means. This 12-month requirement does not apply if the ceiling at the airport is at least 1,000 feet above the lowest MEA, MOCA, or initial approach altitude prescribed for the instrument approach procedure, and the visibility at that airport is at least 3 miles.

Practice example

You are a newly typed First Officer with 60 hours of line operating time in the aircraft type, paired with a line Captain who is not a check pilot. On arrival, ATIS reports a 17-knot crosswind component and braking action medium. Who must fly the landing, and what regulation governs this?

Example answer, written by us. It is not a real applicant's story. The Captain must make the takeoff and landing in this scenario, and the governing regulation is 14 CFR 121.438(a). Because I have fewer than 100 hours of flight time as second in command in Part 121 operations in that airplane type, and the pilot in command is not an appropriately qualified check pilot, the PIC is required to perform all takeoffs and landings whenever specific weather, runway, or airport conditions exist. Here, two separate triggers under 14 CFR 121.438(a)(2) are met: the crosswind component on the runway exceeds 15 knots, and the reported braking action is less than good. Any other trigger, such as prevailing visibility at or below 3/4 mile, RVR at or below 4,000 feet, water, snow, or slush on the runway, reported windshear, or a designated special airport, would also require the Captain to be the pilot flying. Also, under 14 CFR 121.438(b), since I only have 60 hours in type, the Captain must have at least 75 hours of line operating flight time in type for us to legally pair.

This answer names the exact regulation (14 CFR 121.438), identifies both the 100-hour SIC limitation and the 75-hour crew pairing rule, and matches the scenario's numbers to the exact regulatory thresholds (15 knots crosswind and braking action less than good).

Practice this on Fourstripe. Pick your airline and a captain runs the interview out loud: TMAAT, about-you, technical and scenario questions, with real follow-ups. You get a scored report on every answer. 7-day trial, then from $149 a week. Start a practice interview

Frequently asked questions

Is the airline officially named Omni International Airlines?

Federal Aviation Administration regulatory dockets refer to the carrier as Omni Air International rather than Omni International Airlines. Pilots searching for omni international airlines are typically looking for Omni Air International.

Can I fly as a Part 121 second in command with a Restricted ATP in a 3-pilot crew?

No. Under 14 CFR 121.432(a) and 121.436(a), a pilot serving as second in command in a flag or supplemental operation that requires three or more pilots must be fully qualified to act as pilot in command (except for 121.434 operating experience and mentoring ground training), which requires an unrestricted ATP certificate not subject to 14 CFR 61.167 limitations.

How many hours of military flight time can I credit toward the 1,000-hour Part 121 PIC rule?

Under 14 CFR 121.436(c), you may credit up to 500 hours of military flight time toward the 1,000-hour requirement if it was obtained as pilot in command in a multiengine, turbine-powered, fixed-wing airplane or powered-lift aircraft in an operation requiring more than one pilot.

How long do I have to complete the 100-hour consolidation requirement in Part 121?

Under 14 CFR 121.434(g) and (h)(4), you must complete at least 100 hours of line operating flight time (including operating experience) within 120 days of completing your type rating practical test or proficiency check. The certificate holder may extend this window to no more than 150 days if you complete refresher training or a supervised check pilot observation flight on or before the 120th day.

Sources