Part 135 Airline: Operating Rules, Pilot Minimums, and FAA Certification

Short answer: A Part 135 airline is an FAA-certificated air carrier or commercial operator authorized under 14 CFR Part 119 and Part 135 to fly commercial commuter and on-demand missions, bridging private flying (Part 91) and large scheduled airlines (Part 121). According to the Federal Aviation Administration, Part 135 on-demand airplanes are limited to 30 passenger seats or fewer and a 7,500-pound maximum payload, while scheduled Part 135 commuter airplanes are capped at 9 passenger seats, 7,500 pounds of payload, and non-turbojet propulsion. Starting September 30, 2026, initial Part 135 certification applications transition to the FAA Aviation Integrated Safety (AIS) Services portal.

What Is a Part 135 Airline: On-Demand, Commuter, and Part 121 Compared

When pilots and passengers refer to a Part 135 airline or Part 135 airlines, they mean commercial operators certificated under 14 CFR Part 119 and flying under 14 CFR Part 135 (up to date in the Electronic Code of Federal Regulations as of November 9, 2026). Part 135 sits between non-commercial general aviation (Part 91) and large scheduled airlines (Part 121). A Part 135 certificate belongs to your operating company rather than an individual airframe and pairs with legally binding Operations Specifications (OpSpecs) listing authorized aircraft, areas, and operations.

Under FAA Part 135 General Information and 14 CFR 119.5, interstate, foreign, overseas, or postal contract mail carriers receive an Air Carrier Certificate. Operators flying intrastate common carriage wholly within one US state receive an Operating Certificate, as do private or noncommon carriage operators flying for hire under 14 CFR 119.23(b) in airplanes or powered-lift with fewer than 20 passenger seats (excluding crew seats) and less than 6,000 pounds of payload. Part 135 airlines cover executive charters, scheduled commuters, cargo and mail feeders, helicopter air ambulances (Subpart L), commercial air tours, and civil unmanned aircraft systems (UAS). Under FAA Aeronautical Information Manual Chapter 11, Section 4, drone operators conducting commercial package delivery beyond visual line of sight or interstate hazardous materials transport cannot use Part 107 and must hold a Part 135 certificate, Part 11 exemptions, and an Air Traffic Organization Certificate of Waiver or Authorization.

Your carrier will hold either On-Demand or Scheduled (Commuter) authority, subject to the seat, payload, and propulsion limits in the table below. Under 14 CFR 135.2, scheduled passenger service in turbojets of 1 to 30 seats, post-1964 nontransport turboprops of 10 to 19 seats, or transport turboprops of 20 to 30 seats requires Part 121 certification. Under 14 CFR 135.3(b), commuter operations in airplanes type certificated for two pilots must use Part 121 Subparts N and O for crew training and qualification, though second-in-command pilots may qualify under 14 CFR 135.245.

Regulatory comparison of FAA operating frameworks under 14 CFR Parts 91, 135, and 121

Regulatory Feature Part 91 (General & 91.147 Tours) Part 135 On-Demand Part 135 Commuter Part 121 Scheduled Airlines
Part 119 certificate No (LOA for 91.147 tours within 25 statute miles) Yes (Air Carrier or Operating Certificate) Yes (Air Carrier or Operating Certificate) Yes (Air Carrier or Operating Certificate)
Scheduled frequency None permitted Fewer than 5 round trips per week on a route (9 seats or fewer, non-turbojet) Unlimited scheduled routes (plus on-demand) Unlimited scheduled domestic or flag routes
Airplane seat limit 30 seats or fewer for 91.147 air tours 30 passenger seats or fewer 9 passenger seats or fewer Scheduled turbojets (1 to 30+ seats) and turboprops with 10+ seats
Maximum airplane payload 7,500 pounds or less for 91.147 air tours 7,500 pounds (or any rotorcraft) 7,500 pounds (or any rotorcraft) Governed by Part 25 transport category weight limits
Turbojet airplanes Yes (non-common carriage) Yes (up to 30 seats and 7,500 pounds payload) No turbojet aircraft allowed Yes
Part 5 SMS required No under 14 CFR 119.8 Yes under 14 CFR 119.8 Yes under 14 CFR 119.8 Yes under 14 CFR 119.8

The Four Part 135 Certificate Scopes: Single Pilot to Standard

The FAA issues four Part 135 certificate scopes through your Operations Specifications so small operators can launch with reduced administrative overhead and later request an abbreviated scope upgrade through their Flight Standards District Office (FSDO) or Certificate Management Office (CMO). Single-pilot operators (OpSpec A040) are exempt from manuals, training programs, and Part 119 management posts, but must still name operational control officials and hold an approved Hazardous Materials training program. Upgrading from Single Pilot in Command (OpSpec A039, 4 pilots maximum) to 135 Basic (5 pilots maximum) adds only one pilot slot while allowing multiple captains across up to 5 aircraft and 3 aircraft types.

Comparison of FAA Part 135 certificate scopes from FAA General Information

Scope Tier Maximum Pilots Fleet Cap Seat Limit Geographic & Approach Limits Manuals & Management
Single Pilot (OpSpec A040) 1 named pilot Not stated (exclusive use of at least 1 aircraft) Per kind of operation Authorized via OpSpecs Not required (except operational control and HazMat training)
Single PIC (OpSpec A039) 1 PIC and up to 3 SICs (4 total) Not stated 9 passenger seats or fewer US, Canada, Mexico, Caribbean, no Cat II or III Required by rule, FAA deviations available
135 Basic 5 pilots total (including SICs) Up to 5 aircraft across at most 3 types 9 passenger seats or fewer US, Canada, Mexico, Caribbean, no Cat II or III Required, limited FAA deviations possible
Standard Part 135 No pre-set limit No pre-set limit Up to 30 seats on-demand or 9 seats commuter Per OpSpec qualification Full manuals, training, DO, Chief Pilot, and DOM required

Pilot Qualifications, Flight Hour Minimums, and Single-Pilot IFR Rules

Under 14 CFR 135.243(a), you need an Airline Transport Pilot (ATP) certificate to serve as pilot in command (PIC) in passenger-carrying operations involving turbojet airplanes, airplanes or powered-lift with 10 or more passenger seats (excluding crew seats), multiengine commuter airplanes or powered-lift, or scheduled interstate helicopters within the 48 contiguous states. Under 14 CFR 135.244, commuter PICs must also log supervised make-and-basic-model operating experience with a check pilot: 10 hours in single-engine aircraft, 15 hours in multiengine piston aircraft, 20 hours in multiengine turbine aircraft, or 25 hours in turbojets, reducible by up to 50 percent with extra takeoffs and landings. Other VFR and IFR PIC minimums (including the narrow 135.243(d) isolated-area day-VFR single-engine piston exception) and 135.4 Eligible On-Demand two-pilot rules appear in the table below.

Under 14 CFR 135.99, 135.101, and 135.111, a second in command (SIC) is required for passenger aircraft with 10 or more seats, Category II approaches, and passenger IFR flights, unless your OpSpecs authorize an operative approved autopilot in place of an SIC under 14 CFR 135.105 (which requires 100 hours PIC in make and model for commuter flights). Carriers flying single-pilot IFR aircraft can also hold OpSpec approval for a Second-in-Command Professional Development Program (135.99(c)) so SICs can log multi-crew time.

Part 135 pilots must follow flight, duty, and rest rules (14 CFR 135.263 through 135.273), Crew Resource Management training (required since March 22, 2013 under 135.330), and 90-day passenger landing recency (135.247). Recurrent testing includes 12-month knowledge, competency, and PIC line checks (135.293, 135.299) plus 6-month IFR PIC instrument proficiency checks (135.297, with a 12-month single-pilot autopilot check). Under the Pilot Records Improvement Act (PRIA), carriers review 5 years of pilot records and check the FAA Pilot Records Database (PRD). Private Pilots cannot access PRD, and starting mid-November 2026, PRD user accounts deactivate after 365 days of inactivity.

FAA Part 135 pilot qualification thresholds under 14 CFR Subparts E and G

Crew Position Minimum Certificate Minimum Total Time Key Sub-Hour & Recency Rules
VFR PIC (135.243(b)) Commercial + Instrument (airplane/powered-lift) 500 hours 100 hours cross-country, 25 hours night, 12-month checks
IFR PIC (135.243(c)) Commercial + Instrument 1,200 hours 500 hours cross-country, 100 night, 75 instrument (50 actual flight), 6-month IPC
Turbojet, 10+ Seat, or Multiengine Commuter PIC (135.243(a)) ATP + Type Rating if required Per Part 61 ATP rules 10 to 25 hours commuter make/model experience (135.244), 6-month IPC
Standard SIC (135.245) Commercial + Instrument (except VFR helicopter) Per Part 61 Commercial rules 6 approaches, holding, and tracking within 6 calendar months for IFR, 12-month check
Eligible On-Demand Crew (135.4) ATP for multiengine turbine PIC, Commercial + Instrument SIC 1,500 hours PIC, 500 hours SIC 75 hours make/model for one pilot, PIC flying limits if SIC has under 100 hours in type

Ownership, Management, Maintenance, and Safety Mandates

Under 14 CFR Part 119 and FAA General Requirements for Certification, Part 135 applicants must be US citizens. Partnerships require all US citizen partners, while corporations need a US citizen president, at least two-thirds US citizen board directors and managing officers, and at least 75 percent US citizen voting interest (with 5 percent or greater stockholders disclosed on intrastate applications under 119.36). Operators must keep a physical principal base with 30 days written relocation notice (119.47) and hold exclusive use of at least one conforming aircraft owned or leased for at least 6 continuous months from certification (135.25).

Standard Part 135 airlines must appoint a Director of Operations (DO), Chief Pilot, and Director of Maintenance (DOM) under 14 CFR 119.69 and 119.71. If operations require an ATP-rated PIC, both the DO and Chief Pilot need an ATP certificate and at least 3 years of Part 121 or Part 135 PIC experience (earned within the past 6 years for first-time appointees), though the DO may qualify with 3 years of recent Part 121 or Part 135 operational control supervisory experience. Under 14 CFR 119.73, a 2-year bar restricts employing former FAA aviation safety inspectors to represent the carrier before the FAA.

Under 14 CFR 135.411, aircraft type certificated for 9 passenger seats or fewer follow Parts 91 and 43 plus supplemental Part 135 rules or an Approved Aircraft Inspection Program (AAIP), with procedures typically in the General Operations Manual (GOM). Aircraft with 10 or more passenger seats require a Continuous Airworthiness Maintenance Program (CAMP) under 135.423 through 135.443 and a three-part General Maintenance Manual (GMM). Carriers must follow manufacturer-recommended Time Between Overhauls (TBOs), restore time-limited or cycle-limited parts with incomplete records to zero-time status before FAA conformity checks, and hold an approved Minimum Equipment List (MEL) and OpSpec to dispatch with inoperative equipment.

  • Part 5 Safety Management System (SMS): Under 14 CFR 119.8 (amended April 26, 2024), all Part 135 certificate holders must maintain a Part 5 SMS.
  • Hazardous Materials Program: Under Part 135 Subpart K, every operator, including single-pilot and will-not-carry operators, needs an FAA-approved HazMat training program.
  • Drug, Alcohol, and TSA Programs: Carriers must run a Part 120 drug and alcohol testing program administered by AAM-820 and adopt applicable TSA security programs under 49 CFR 1544.101.
  • Supplemental Restraint Systems (SRS) Final Rule: Following the March 11, 2018 East River open-door helicopter ditching in which five passengers drowned, FAA Final Rule Docket No. FAA-2023-2250 (Amendment 135-146, scheduled for Federal Register publication August 22, 2024) bars civil SRS flights unless harnesses use FAA-approved attachment points, release rapidly without cutting, and include passenger briefings under 14 CFR 135.117(g) and 91.108.

The 5-Phase FAA Certification Process and AIS Services

Under 14 CFR 119.35(b), applicants must file at least 90 days before intended operations and clear a 5-phase, 3-gate review. Starting September 30, 2026, initial Part 135 applications move from the Safety Assurance System (SAS) to Aviation Integrated Safety (AIS) Services (formerly AVS Hub) under Notice 8900.766, accepting PDF, Excel, and Word files up to 500MB per document. Interstate carriers file OST Form 6410 insurance under 14 CFR Part 205, with interstate commuters securing DOT economic authority and interstate on-demand operators filing OST Form 4507 Air Taxi registration at least 30 days before starting flights.

  • Phase 1, Pre-application (Gate 1): File FAA Form 8400-6 Pre-application Statement of Intent (PASI), pass Certification Service Oversight Process (CSOP) resource screening (or wait-listing), and complete the Pre-application Meeting.
  • Phase 2, Formal Application (Gate 2): Submit the Formal Application Letter, Schedule of Events, Compliance Statement, GOM and GMM manuals, training curricula, management resumes, aircraft ownership or lease records, and proposed OpSpecs, ending with a Formal Application Meeting.
  • Phase 3, Design Assessment: FAA inspectors audit manuals, maintenance programs, and training curricula against 14 CFR rules.
  • Phase 4, Performance Assessment (Gate 3): Inspectors evaluate training, aircraft conformity, and simulated operations, including at least 25 hours of proving tests for first-time Part 135 turbojet or VFR two-pilot aircraft.
  • Phase 5, Administrative Functions: The FAA issues the certificate and signed OpSpecs once Title 49 U.S.C. and 14 CFR compliance is verified. Carriers ending Part 135 operations must surrender both within 30 days (119.61(c)).

Checklist: Verifying a Legal Part 135 Carrier

Under 14 CFR 119.5 and 135.7, advertising or flying commercial charter without a valid certificate and Operations Specifications is illegal. Use this four-point checklist written by our team from 14 CFR Part 119 before booking a charter or accepting a contract flight.

  • Match the business name to OpSpecs (14 CFR 119.9(a)): Confirm that the exact company or doing-business-as name on your charter quote is listed as an authorized business name on the carrier's Operations Specifications.
  • Verify the tail number on OpSpecs (14 CFR 119.49(a)(4)): Ask the operator to show that your assigned aircraft registration marking and serial number appear on its Operations Specifications.
  • Inspect ramp markings before boarding (14 CFR 119.9(b)): Verify that the operating certificate holder's legal name or certificate number is legibly displayed on the aircraft exterior and readable from the ground.
  • Confirm wet-lease or sub-charter control (14 CFR 119.53): If another operator flies a substitute aircraft, verify which Part 135 carrier holds FAA operational control and DOT economic authority.

How to Prepare for a Part 135 Pilot Interview

Part 135 Chief Pilot interviews evaluate your Subpart E logbook legality, IFR decision-making, and direct passenger communication without a Part 121 dispatch desk. Follow this three-step plan written by our team to prepare.

Step 1 (Audit 135.243 sub-hours and PRD access): Break out total time, point-to-point cross-country, night, and actual flight instrument hours against 14 CFR 135.243(c), and log into your FAA Pilot Records Database account at least once every 365 days so employer record sharing stays active.

Step 2 (Review 135.293 oral testing subjects): Study aircraft systems, takeoff and landing weight and balance, ground deicing holdover procedures (135.345), Minimum Equipment List deferrals, and emergency deviation reports (due within 10 days excluding Saturdays, Sundays, and Federal holidays under 135.19(c)).

Step 3 (Practice telling your own stories out loud): Rehearse real examples from your flying career where you managed weather pressure, resolved a preflight discrepancy, or briefed passengers clearly during a delay.

Practice example

You are scheduled to fly a passenger-carrying IFR trip single-pilot in a light turboprop, and during preflight you find the autopilot pitch channel is inoperative. The weather is 800 overcast and 2 miles visibility, and the passengers are running late. How do you handle this?

Example answer, written by us. It is not a real applicant's story. I would delay the departure immediately and keep the passengers comfortable inside the terminal while I check our regulatory options. Under 14 CFR 135.101, carrying passengers under IFR requires a qualified second in command unless we meet the 14 CFR 135.105 exception, which demands both appropriate Operations Specifications and an operative, approved autopilot system. Even if our Minimum Equipment List permits ferrying the aircraft under VFR with an inoperative autopilot, we cannot legally launch single-pilot with passengers into 800-foot ceilings under IFR. I would call Flight Control and the Director of Maintenance right away to pursue two parallel fixes: having maintenance troubleshoot or reset the pitch channel, or assigning a qualified Part 135 second in command who meets 14 CFR 135.245 recency. Once I know which option gives us a legal aircraft and crew, I will brief the passengers honestly on our new departure time.

This answer cites the exact single-pilot IFR autopilot rule in 14 CFR 135.101 and 135.105 without guessing, separates Minimum Equipment List deferral from passenger-carrying IFR crew legality, and shows calm coordination with maintenance, operational control, and passengers.

Practice this on Fourstripe. Pick your airline and a captain runs the interview out loud: TMAAT, about-you, technical and scenario questions, with real follow-ups. You get a scored report on every answer. 7-day trial, then from $149 a week. Start a practice interview

Frequently asked questions

Can a Part 135 airline fly scheduled passenger flights?

Yes. A Part 135 airline with Commuter authority can fly unlimited scheduled passenger routes in rotorcraft or in non-turbojet airplanes with 9 passenger seats or fewer and a 7,500-pound maximum payload. On-Demand operators can fly fewer than 5 scheduled round trips per week on a route in non-turbojet airplanes with 9 passenger seats or fewer.

What is the difference between a Part 135 Air Carrier Certificate and an Operating Certificate?

The FAA issues an Air Carrier Certificate for interstate, foreign, or overseas transportation, or carrying mail. An Operating Certificate covers intrastate common carriage wholly within one US state, or private and noncommon carriage for hire in airplanes or powered-lift with fewer than 20 passenger seats and less than 6,000 pounds of payload.

How many flight hours do you need to fly for a Part 135 airline?

Under 14 CFR 135.243, serving as pilot in command requires 500 total hours for VFR, 1,200 total hours for IFR, or an Airline Transport Pilot certificate for passenger turbojets, airplanes with 10 or more passenger seats, and multiengine commuter flights. Standard second-in-command duty under 14 CFR 135.245 requires a Commercial Pilot Certificate and instrument rating, while 14 CFR 135.4 Eligible On-Demand crews need 500 SIC hours.

When is a second pilot required on a Part 135 flight?

Under 14 CFR 135.99, 135.101, and 135.111, a second in command is required when carrying passengers in aircraft with 10 or more passenger seats, during Category II approaches, or on passenger IFR flights. Under 14 CFR 135.105, passenger IFR flights may operate single-pilot if an operative approved autopilot is authorized via Operations Specifications and commuter PICs have 100 hours PIC in make and model.

How far in advance must a startup Part 135 airline apply to the FAA?

Under 14 CFR 119.35(b), applicants must submit their FAA certificate application at least 90 days before intended operations, and interstate on-demand carriers must file OST Form 4507 Air Taxi registration at least 30 days prior to starting flights. Final certification depends on completing all five FAA phases, CSOP resource screening, and conformity checks.

Sources