RVSM, ETOPS, and Oceanic Airspace Pilot Interview Questions
Short answer: Under 14 CFR Part 91 Appendix G, Reduced Vertical Separation Minimum (RVSM) airspace applies from FL 290 to FL 410 inclusive, where air traffic control reduces vertical separation between approved aircraft from 2,000 feet to 1,000 feet. Operating in this airspace requires two independent primary altimeter systems, an automatic altitude control system that holds altitude within plus or minus 65 feet in nonturbulent air, an altitude alerter, and an altitude-reporting transponder. Airline technical interviews test these specific equipment limits alongside Extended Operations (ETOPS) critical fuel rules under 14 CFR 121.646 and oceanic contingency procedures.
RVSM boundaries, required equipment, and tolerances
Major, cargo, and international airline technical interviews evaluate your command of high-altitude airspace regulations. Under 14 CFR Part 91 Appendix G, RVSM airspace applies from FL 290 to FL 410 inclusive. Within this vertical band, air traffic control provides 1,000 feet of vertical separation between approved aircraft. Utilizing all RVSM flight levels adds six cruising altitudes: FL 300, FL 320, FL 340, FL 360, FL 380, and FL 400.
Cruising levels follow the Flight Level Orientation Scheme in FAA AIM Section 4-6-2. Flights on magnetic courses from 000 to 179 degrees fly odd flight levels, while magnetic courses from 180 to 359 degrees fly even flight levels up to and including FL 410.
Under 14 CFR Part 91 Appendix G and FAA Advisory Circular 91-85B, an aircraft must carry four specific systems with tight operating tolerances to operate in RVSM airspace. Interview evaluation panels expect candidates to recite these systems and their exact performance limits without hesitating.
- At least one automatic altitude control system capable of holding altitude within plus or minus 65 feet in straight and level flight under nonturbulent conditions (or plus or minus 130 feet for legacy aircraft with type certification applications on or before April 9, 1997, using flight management system inputs).
- An altitude alert system signaling deviations greater than plus or minus 200 feet for aircraft certified after April 9, 1997 (or plus or minus 300 feet for applications on or before April 9, 1997).
- An operative altitude-reporting transponder.
- TCAS II meeting TSO C-119b Version 7.0 or later, if TCAS II is installed (Version 7.1 is mandatory across the North Atlantic region since January 1, 2017).
RVSM Altimetry and Autopilot Tolerances (14 CFR Part 91 Appendix G and AC 91-85B)
| System or Check | Regulatory Limit | Condition or Applicability |
|---|---|---|
| Pre-takeoff altimeter check | Max 75 feet difference | Between field elevation (with QNH set) and displayed elevation |
| In-flight primary altimeter cross-check | Manufacturer/AFM limits | Cross-check between the two primary altimeters at cruise |
| Automatic altitude control (autopilot) | Plus or minus 65 feet | Straight and level flight in nonturbulent conditions |
| Legacy autopilot with FMS inputs | Plus or minus 130 feet | Type certification application on or before April 9, 1997 |
| Altitude alert system (modern) | Plus or minus 200 feet | Type certification application after April 9, 1997 |
| Altitude alert system (legacy) | Plus or minus 300 feet | Type certification application on or before April 9, 1997 |
| Altitude select control panel | Plus or minus 25 feet | Max error between flightcrew display and control system output |
| Altimetry system error (ASE) limit | Max 200 feet | Operating under Part 91 Appendix G Section 9(b) |
ADS-B Out authorization and non-RVSM accommodation
A standard follow-up question covers operational authorization. Under 14 CFR Part 91 Appendix G Section 9 and AC 91-85B, operators can fly in domestic U.S. RVSM airspace without a specific Letter of Authorization (LOA) or Operations Specification (OpSpec) if the aircraft carries a qualified ADS-B Out system meeting 14 CFR 91.227. Height-keeping performance is continually monitored by ground systems, and all aircraft in the fleet must have been monitored within the previous 24 months with an altimetry system error not exceeding 200 feet. Flights outside U.S. airspace in countries requiring specific approval still require an LOA or OpSpec B046 under Section 3.
On an ICAO flight plan, an RVSM-compliant operator enters the letter W in Block 10. Non-RVSM flights omit W so ATC automation displays the proper indicator (a coral box around the altitude segment of the controller data block per FAA Order JO 7210.3EE). AIM Section 4-6-4 emphasizes that writing NON-RVSM in Field 18 remarks while leaving W in Field 10 prevents automation from detecting non-RVSM status.
Under AIM Section 4-6-10 and FAA Order JO 7210.3EE, ATC accommodates non-RVSM aircraft on a workload-permitting basis, applying a 2,000-foot vertical separation standard between non-RVSM aircraft and all other traffic.
- Department of Defense aircraft and specified DoD-certified NASA aircraft (T38, F15, F18, WB57, S3, and U2).
- Active air ambulance flights using a MEDEVAC call sign.
- Manufacturer flights for aircraft certification and development.
- Foreign State government aircraft.
- Non-RVSM flights climbing to or descending from FL 430 or above without an intermediate level-off at a normal rate of climb or descent.
- In oceanic airspace: initial delivery flights, formerly approved aircraft flying to maintenance after equipment failure, humanitarian flights, and aircraft in Oakland, Anchorage, or Arctic FIRs transporting a spare wing-mounted engine.
In-flight contingencies, ATC phraseology, and error reporting
Technical panels frequently present equipment failure scenarios at cruise. Per AIM Table 4-6-9, if you cannot maintain your flight level or doubt altitude-keeping capability, take four immediate actions: notify ATC, maintain assigned flight level while evaluating the issue, scan for traffic visually and on TCAS, and turn on exterior lights.
Subsequent actions depend on the failure. If one primary altimeter fails, cross-check the remaining primary against standby and notify ATC of single-primary operation. If all primary altimeters fail, or if the autopilot or altitude alerter fails, state to ATC: Unable RVSM Due Equipment. Request clearance out of RVSM airspace, or ATC will provide 2,000 feet vertical separation.
Severe turbulence and Mountain Wave Activity (MWA) are tested using the same logic. If weather causes altitude excursions of about 200 feet or greater, notify ATC and state: Unable RVSM Due Turbulence, or Unable RVSM Due Mountain Wave. Because aircraft separation is the controller's primary duty under FAA Order JO 7110.65, ATC applies merging target vectors to prevent radar targets from overlapping with traffic at adjacent flight levels.
Under 14 CFR Part 91 Appendix G Section 6, operators must report specific altitude-keeping performance errors to the FAA Administrator.
- Total Vertical Error (TVE) of 300 feet or more.
- Altimetry System Error (ASE) of 245 feet or more.
- Assigned Altitude Deviation (AAD) of 300 feet or more.
Standard RVSM Pilot and Controller Phraseology (FAA AIM Table 4-6-1)
| Situation | Speaker | Required Phraseology |
|---|---|---|
| Controller verifying RVSM approval | Controller | (Call sign) confirm RVSM approved |
| Pilot confirming RVSM approval | Pilot | Affirm RVSM |
| Pilot reporting non-RVSM status | Pilot | Negative RVSM (plus details, e.g., Certification flight) |
| Loss of autopilot, alerter, or primary altimeters | Pilot | Unable RVSM Due Equipment |
| Weather deviation of about 200 feet or more | Pilot | Unable RVSM due (state reason, e.g., turbulence, mountain wave) |
| Ready to return to RVSM after contingency | Pilot | Ready to resume RVSM |
NAT HLA SLOP and oceanic contingency procedures
Operating across North Atlantic High Level Airspace (NAT HLA) introduces distinct procedures from domestic airspace. Under the FAA North Atlantic Resource Guide and ICAO Doc 4444, aircraft operating in oceanic airspace may fly Strategic Lateral Offset Procedures (SLOP). SLOP mitigates wake turbulence encounters and reduces collision risk from highly accurate navigation overlap. In contrast, domestic U.S. airspace strictly prohibits uncoordinated offsets. In domestic airspace, pilots must request and obtain an ATC clearance before flying any lateral offset.
When an in-flight contingency occurs in NAT HLA, such as an engine failure or severe depressurization, and the flight crew cannot obtain a revised ATC clearance immediately, oceanic contingency procedures apply per ICAO Doc 4444 and the NAT Resource Guide.
ETOPS thresholds, aircraft systems, and critical fuel planning
Extended Operations (ETOPS) rules govern long-range flight. Under 14 CFR 121.161 and the FAA ETOPS Final Rule (72 FR 1808), two-engine Part 121 airplanes cannot operate routes with points beyond 60 minutes flying time at approved single-engine cruise speed in still air from an Adequate Airport without ETOPS approval (OpSpec B342). For passenger airplanes with more than two engines, ETOPS applies beyond 180 minutes (OpSpec B344), while 14 CFR 121.646(a) decompression fuel rules apply whenever flying more than 90 minutes from an Adequate Airport at all-engine cruise power.
Long-range flight planning also requires evaluating the Equal Time Point (ETP). An ETP represents a geographical position along the route where the flight time to divert to two designated suitable alternates is exactly equal. ETP calculations depend on groundspeed, distance between airports, and wind components. If an engine failure or pressurization event occurs before the ETP, turning back to the departure alternate is faster. Beyond the ETP, proceeding to the forward alternate saves time.
Under Part 25 Appendix K (K25.1.3(b)), all ETOPS type-design airplanes must have at least three independent electrical generation sources regardless of diversion time. Time-limited systems such as Class C cargo fire suppression must support the maximum diversion time plus 15 minutes for holding or go-around. ETOPS alternates require Rescue and Firefighting Services of at least ICAO Category 4. Beyond 180 minutes, satellite-based voice communication (SATCOM voice) is required under 14 CFR 121.99 and 121.122 (operable everywhere except north of 82 degrees latitude).
Under 14 CFR 121.646(b), ETOPS dispatch requires evaluating fuel from the most critical point to an alternate under three failure scenarios and boarding the greatest amount, adjusted for wind, icing, deterioration, holding, and APU consumption.
- Scenario A: Rapid decompression at the critical point, descending to a safe altitude under 14 CFR 121.333.
- Scenario B: Simultaneous rapid decompression and engine failure at the critical point, flying at single-engine speed at a safe oxygen altitude.
- Scenario C: Engine failure alone at the critical point, flying at single-engine cruise speed and altitude.
- Wind forecast penalty: Increase forecast wind speed by 5% (higher headwind or lower tailwind). If not using an FAA-accepted wind model, carry an extra 5% of scenario fuel as reserve.
- Engine deterioration: Add 5% to the fuel calculation unless the airline has an approved in-service fuel monitoring program.
- Holding, approach, and landing: Fuel to hold for 15 minutes at 1,500 feet above field elevation, fly an instrument approach, and land.
- APU fuel: Account for APU fuel burn if it is a required power source.
Worked calculation: ETOPS critical fuel under 14 CFR 121.646(b)
To illustrate how these regulatory factors combine on dispatch calculations, here is a worked example constructed by our team using the exact formulas in 14 CFR 121.646(b).
A twin-engine jet reaches its most critical point. Baseline wind-adjusted diversion fuel burns are: 11,800 pounds for engine failure only, 13,500 pounds for decompression only, and 14,000 pounds for simultaneous decompression and engine failure. The carrier lacks an in-service fuel deterioration monitoring program. Icing is forecast for 60 minutes, where airframe icing plus anti-ice burns 2,400 pounds per hour, while engine and wing anti-ice alone burns 400 pounds per hour. Holding for 15 minutes at 1,500 feet plus approach requires 1,600 pounds, and APU fuel burn is 300 pounds.
By our calculation from 14 CFR 121.646(b), compute the critical fuel in five steps.
- Step 1 (Select limiting failure): Compare 11,800 lbs, 13,500 lbs, and 14,000 lbs. The simultaneous failure is greatest at 14,000 pounds.
- Step 2 (Add 5% deterioration penalty): Multiply 14,000 lbs by 5%, adding 700 pounds.
- Step 3 (Select greater icing option): Option A is 10% of 60 minutes (0.1 hr) at 2,400 lbs/hr = 240 pounds. Option B is 100% of 60 minutes (1.0 hr) at 400 lbs/hr = 400 pounds. Add the greater value: 400 pounds.
- Step 4 (Add 15-minute hold and approach): Add 1,600 pounds.
- Step 5 (Add APU consumption): Add 300 pounds. Total required ETOPS critical fuel is 14,000 + 700 + 400 + 1,600 + 300 = 17,000 pounds.
15 RVSM, ETOPS, and oceanic pilot interview questions and answers
Practice speaking these 15 technical interview answers out loud. Every answer below is a model response written by our team to sound like a pilot speaking across the interview table.
-
What are the altitude boundaries and vertical separation minimums of RVSM airspace? Under 14 CFR Part 91 Appendix G, RVSM airspace extends from FL 290 through FL 410 inclusive. Within this altitude stratum, air traffic control provides 1,000 feet of vertical separation between approved aircraft, whereas conventional vertical separation of 2,000 feet applies above FL 410 or to non-approved flights.
-
What aircraft equipment is required to enter RVSM airspace? Under Part 91 Appendix G, the aircraft must have two independent primary altimeter systems, one altitude alerter, one automatic altitude control system, and an operative altitude-reporting transponder. If TCAS II is installed, it must be Version 7.0 or later, with Version 7.1 mandatory across the North Atlantic region.
-
What in-flight cross-check tolerance is required between the two primary altimeters? During cruise in RVSM airspace, I cross-check the two primary altimeters periodically according to aircraft flight manual specifications. If they diverge beyond operating limits, I cross-check against the standby altimeter to determine which primary system is reliable, or report the loss of RVSM capability to ATC.
-
What is the holding tolerance for an autopilot in RVSM airspace? In straight and level flight under nonturbulent conditions, the automatic altitude control system must hold altitude within plus or minus 65 feet of acquired level. For legacy aircraft certified on or before April 9, 1997, equipped with flight management system inputs, the tolerance is plus or minus 130 feet.
-
What are the altitude alerter activation limits and the ground altimeter check tolerance? For modern aircraft certified after April 9, 1997, the altitude alerter must warn the crew whenever displayed altitude deviates from selected altitude by more than plus or minus 200 feet. Before takeoff, with local QNH set, the primary altimeters must read within 75 feet of known field elevation.
-
You are cruising at FL 370 and your autopilot fails. What are your immediate actions and ATC phraseology? I immediately hand-fly to maintain FL 370, scan TCAS and visually for traffic, and turn on exterior lights to alert nearby crews. Then I call ATC and state: Unable RVSM Due Equipment. I request clearance out of RVSM airspace, or ATC will provide 2,000 feet vertical separation.
-
How does ATC accommodate non-RVSM aircraft climbing through RVSM flight levels? Under AIM Section 4-6-11, ATC can accommodate non-RVSM aircraft climbing to or descending from FL 430 or above on a workload-permitting basis. The flight must make a continuous climb or descent at a normal rate without leveling off. ATC applies 2,000 feet separation, and I state Negative RVSM on initial contact and readbacks.
-
What altitude-keeping error thresholds must an operator report to the FAA? Under Part 91 Appendix G Section 6, operators must report a Total Vertical Error of 300 feet or more, an Altimetry System Error of 245 feet or more, or an Assigned Altitude Deviation of 300 feet or more.
-
You encounter mountain wave activity causing 200-foot altitude excursions. What do you report to ATC, and what will the controller do? When weather induces altitude excursions of about 200 feet or greater, I contact ATC immediately and state: Unable RVSM Due Mountain Wave, giving the location and severity. The controller's primary duty is to apply merging target vectors to ensure targets do not merge with traffic at adjacent flight levels.
-
Can you fly a lateral offset for wake turbulence in domestic U.S. airspace versus NAT HLA? In domestic U.S. airspace, I cannot fly an offset without an explicit ATC clearance. However, in North Atlantic High Level Airspace, Strategic Lateral Offset Procedures allow me to offset to the right of centerline up to 2.0 nautical miles without an ATC clearance to mitigate wake or navigation overlap.
-
What initial steps do you take during an emergency descent or contingency in NAT HLA if you cannot contact ATC? If I am unable to obtain a clearance, I turn at least 30 degrees right or left to establish a 5 NM parallel offset track.
-
What defines the regulatory time threshold for ETOPS under 14 CFR Part 121? Under 14 CFR 121.161, a two-engine airplane requires ETOPS approval when operating routes with points beyond 60 minutes flying time at approved single-engine cruise speed in still air from an Adequate Airport. For passenger airplanes with more than two engines, ETOPS applies beyond 180 minutes, while decompression fuel rules apply beyond 90 minutes at all-engine cruise.
-
What is an Equal Time Point in long-range flight planning? An Equal Time Point represents a geographical position along the route where the flight time to divert to two designated suitable alternates is equal, based on groundspeed, distance between airports, and wind components. If an emergency occurs before the ETP, turning back to the departure alternate is faster. beyond the ETP, proceeding to the forward alternate saves time.
-
What three failure scenarios determine ETOPS critical fuel planning? Under 14 CFR 121.646(b), dispatch evaluates the fuel required from the critical point to an alternate under rapid decompression alone, simultaneous rapid decompression and engine failure at single-engine speed, and engine failure alone at single-engine speed. The airplane must carry whichever quantity is greatest, plus allowances for winds, icing, deterioration, APU burn, and a 15-minute hold.
-
Why is SATCOM voice required beyond 180 minutes, and how many electrical sources must an ETOPS aircraft have? Under Part 25 Appendix K, every ETOPS aircraft must have at least three independent electrical power generation sources. SATCOM voice is mandatory beyond 180 minutes because line-of-sight VHF is unavailable, HF voice suffers from severe static and solar flare dropouts, and typing datalink messages during an emergency creates unacceptable cockpit workload and heads-down distraction.
Practice example
You are cruising at FL 360 over the western United States when your aircraft encounters severe mountain wave activity, causing altitude excursions of 250 feet and airspeed fluctuations. Walk me through your immediate cockpit actions, your exact radio call to ATC, and what you expect the controller to do.
Example answer, written by us. It is not a real applicant's story. First, I focus on flying the aircraft, maintaining FL 360 and safe airspeed within buffet limits, while scanning visually and on TCAS for traffic and turning on exterior lights. Because weather deviations have reached 200 feet or more, FAA AIM Section 4-6-6 requires an immediate radio call using standard phraseology. I state our call sign, FL 360, Unable RVSM Due Mountain Wave, and report the location and magnitude. In response, the controller has a priority duty under merging target procedures to issue radar vectors to us or traffic at adjacent flight levels so targets do not merge while vertical separation is compromised. If vectors are not issued immediately, I request a vector clear of FL 350 and FL 370 traffic, followed by an altitude change or reroute.
This answer follows the exact sequence in FAA AIM Table 4-6-9: maintain aircraft control and increase visibility first, deliver the verbatim phraseology required at the 200-foot deviation threshold, and explain ATC merging target procedures before asking for a new altitude.
Practice this on Fourstripe. Pick your airline and a captain runs the interview out loud: TMAAT, about-you, technical and scenario questions, with real follow-ups. You get a scored report on every answer. 7-day trial, then from $149 a week. Start a practice interview
Frequently asked questions
What equipment is required to fly in RVSM airspace?
Under 14 CFR Part 91 Appendix G, an aircraft must have two independent primary altitude measurement systems, at least one automatic altitude control system holding within plus or minus 65 feet in nonturbulent air, an altitude alert system, and an operative altitude-reporting transponder. If equipped with TCAS II, it must meet Version 7.0 or later (Version 7.1 in the North Atlantic).
What phraseology do you use if turbulence prevents maintaining altitude in RVSM airspace?
Under FAA AIM Section 4-6-6, when experiencing weather-induced altitude deviations of about 200 feet or more, contact ATC and state 'Unable RVSM Due Turbulence' or 'Unable RVSM Due Mountain Wave.' Controllers then apply merging target vectors to keep your radar target from overlapping with traffic at adjacent levels.
What vertical separation is applied to non-RVSM aircraft in RVSM flight levels?
Under FAA AIM Section 4-6-10, ATC applies a 2,000-foot vertical separation standard between any non-RVSM aircraft and all other aircraft operating between FL 290 and FL 410 inclusive. Approved non-RVSM flights such as DoD or MEDEVAC are accommodated on a workload-permitting basis.
Do I need a specific Letter of Authorization for domestic RVSM flights?
No, not if your aircraft complies with 14 CFR Part 91 Appendix G Section 9 using a qualified ADS-B Out system meeting 14 CFR 91.227, maintains an altimetry system error of 200 feet or less, and has been monitored within the previous 24 months. Foreign airspace requiring specific approval still requires an OpSpec, MSpec, or LOA under Appendix G Section 3.
What are the components of the ETOPS critical fuel scenario?
Under 14 CFR 121.646(b), critical fuel covers the most limiting of three failures (decompression, engine failure, or simultaneous decompression and engine failure) adjusted for a 5% wind penalty, plus 5% engine deterioration (unless monitored), icing fuel, APU fuel if required, and a 15-minute hold at 1,500 feet followed by an instrument approach and landing.
Sources
- 14 CFR Part 91 Appendix G: Operations in Reduced Vertical Separation Minimum (RVSM) Airspace
- 14 CFR 121.646: En-route Fuel Supply for Flag and Supplemental Operations
- FAA Aeronautical Information Manual (AIM) Chapter 4, Section 6: Operational Policy/Procedures for RVSM
- FAA Advisory Circular 91-85B: Authorization of Aircraft and Operators for Flight in RVSM Airspace
- FAA Order JO 7210.3EE Chapter 6, Section 8: Facility Operation and Administration, RVSM
- FAA North Atlantic (NAT) Resource Guide for United States Operators
- FAA Final Rule: Extended Operations (ETOPS) of Multi-Engine Airplanes (72 FR 1808)
- FAA Proposed Rule: Reduced Vertical Separation Minimum in WATRS and TCAS II Version 7.0 (65 FR 79284)