Type Rating in Aviation: Requirements, 12,500-Pound Rules, FAA vs. EASA Designations, and Checkrides

Short answer: In aviation, a type rating is a model-specific certification added to your pilot certificate to operate designated large, turbojet, or multi-pilot aircraft beyond standard category and class privileges. FAA Order 8900.1 Figure 5-88 lists required civil designations, including aircraft operated above 12,500 pounds maximum takeoff weight. Under FAA Notice N 8900.225 and 14 CFR 121.436, both Captains and First Officers in Part 121 airline operations must also hold an Airline Transport Pilot (ATP) or Restricted Privileges ATP certificate with an appropriate aircraft type rating. You earn one through model-specific training and an ATP-standard checkride under FAA-S-ACS-11A.

What Is a Type Rating in Aviation (Class Ratings vs. Endorsements, Explained)

The type rating meaning in aviation comes down to the boundary between broad aircraft classes and model-specific authorizations, which defines what is a type rating aviation regulators require on a pilot certificate. Under 14 CFR Part 61 and the Airman Certification Standards Companion Guide for Pilots (FAA-G-ACS-2, Change 2 dated December 26, 2024), airplane class ratings group light aircraft into Airplane Single-Engine Land (ASEL), Airplane Multiengine Land (AMEL), Airplane Single-Engine Sea (ASES), and Airplane Multiengine Sea (AMES). European rules under Commission Regulation (EU) No 1178/2011 (Part-FCL, sections FCL.010 and FCL.700) similarly group light airplanes into Single-Engine Piston (SEP), Multi-Engine Piston (MEP), Single-Engine Turboprop (SET), and Touring Motor Glider (TMG) classes.

Stepping up to a faster light airplane within a class only requires instructor-signed training rather than a new certificate line. On the EASA Aeroplanes Endorsement List (updated February 12, 2026), SEP variants such as variable-pitch propellers (VP), retractable undercarriage (RU), turbo-charged or super-charged engines (T), cabin pressurization (P), tail wheels (TW), electronic flight instrument systems (EFIS), and single-lever power control (SLPC) are handled inside the class rating through differences or familiarization training.

A type rating is a permanent certificate privilege tied to one aircraft make, model, or variant family, such as B-737, A-320, or CE-525. Earning one requires model-specific ground and flight or Flight Simulation Training Device (FSTD) training, an application on FAA Form 8710-1 (or to a European National Competent Authority), and an ATP-standard practical test. Under FAA Order 8900.1, Volume 5, Chapter 2, Section 19, Figure 5-88 (dated October 27, 2026), the FAA began removing marketing names in November 2015, so always match Block 2 of the Airworthiness Certificate to the Civil Model Designation column.

When Do You Need a Type Rating and How the 12,500-Pound Rule Works

Under 14 CFR 61.31 (referenced in FAA Order 8900.1 Change 997A), three operational triggers determine when you need a type rating. First, under federal type rating requirements 12,500 pounds maximum takeoff weight is the threshold above which large aircraft require a dedicated rating, alongside turbojet-powered airplanes of any weight. In the FAA airplane type designation table, a Viking Air DHC-6-300 Twin Otter requires the DHC-6 rating when Supplemental Type Certificate (STC) SA02267LA applies for restricted-category operations above 12,500 pounds maximum takeoff weight, while STC SA02682LA places the DHC-6-300HG in the commuter category under DHC-6HG. Heavy turboprops and piston airliners like the Beechcraft 300/B300 (BE-300), Beech 1900 (BE-1900), ATR 42/72 (ATR-42, ATR-72), and Douglas DC-3 (DC-3) also carry dedicated ratings. Every turbojet requires a type rating too, including light jets such as the Cirrus SF50 (SF-50), HondaJet (HA-420), Eclipse 500 (EA-500 or EA-500S), and Citation Mustang (CE-510 or CE-510S).

Second, all Part 121 airline pilots must hold an aircraft type rating regardless of seat. Under 14 CFR 121.436, every Pilot in Command (PIC) and Second in Command (SIC) in Part 121 operations must hold an appropriate aircraft type rating, effective August 1, 2013 for new-hire First Officers and January 1, 2016 for incumbent Part 121 SICs. A Second-in-Command-only type rating issued under 14 CFR 61.55 (used for non-airline international multi-pilot compliance) does not satisfy 14 CFR 121.436(b).

Third, business jets split into multi-pilot and single-pilot designations. Large-cabin jets like the Challenger 300 (CL-30) and Gulfstream G650 (GVI) require two pilots, whereas optional single-pilot jets use distinct codes or limitations. On Citation 525, 525A, 525B, and 525C models, a crewed checkride issues CE-525 (SIC Required) and a single-pilot checkride issues CE-525S, while Embraer EMB-500 and EMB-505 ratings add an SIC limitation when tested with a crew.

FAA Part 121 and Part 61 pilot certificate and type rating rules from FAA Notice N 8900.225

Crew Role or Certificate Path Required Pilot Certificate Type Rating Requirement Minimum Medical and Operational Experience
Part 121 Pilot in Command (14 CFR 121.436) Unrestricted ATP certificate under 14 CFR 61.159 Full aircraft type rating for the aircraft flown First-class medical, 1,500 hours total time, plus 1,000 air carrier hours (up to 500 military multi-pilot turbine PIC hours credited)
Part 121 Second in Command, Standard Two-Pilot Crew (14 CFR 121.436) Unrestricted ATP or Restricted Privileges ATP under 14 CFR 61.160 Full aircraft type rating (14 CFR 61.55 SIC rating is not accepted) At least a second-class medical certificate and completion of ATP CTP prior to ATP knowledge test
Part 121 Second in Command, Flag or Supplemental With 3 or More Pilots Unrestricted ATP certificate under 14 CFR 61.159 (R-ATP not accepted) Full aircraft type rating for the aircraft flown First-class medical certificate and 1,500 hours total pilot time
Non-Part 121 Second in Command Rating (14 CFR 61.55) Underlying pilot certificate appropriate to the operation SIC-only pilot type rating issued under 14 CFR 61.55 Valid outside Part 121 where an SIC type rating is needed, excluded from Part 121 air carrier service

Requirements for a Type Rating and the ATP CTP Prerequisite

Requirements for a type rating depend on whether you add the rating to an existing Private, Commercial, or ATP certificate, or earn it concurrently with an initial multiengine ATP certificate. Regardless of certificate level, every airplane type rating checkride is evaluated to ATP proficiency standards under the Airline Transport Pilot and Type Rating for Airplane Category Airman Certification Standards (FAA-S-ACS-11A, published April 2024 and effective May 31, 2024).

Do not confuse a type rating with the Airline Transport Pilot Certification Training Program (ATP CTP). Under 14 CFR 61.156 and AC 61-138, anyone seeking an ATP multiengine class rating or an ATP certificate issued concurrently with an airplane type rating must present an ATP CTP graduation certificate from an authorized Part 121, 135, 141, or 142 provider before taking the ATP Multiengine (ATM) knowledge test (mandatory after July 31, 2014). Under 14 CFR 61.35, you must be at least 18 to take the ATM test, and passing results completed after July 31, 2014 remain valid for 60 calendar-months.

Under FAA Notice N 8900.225, the 14 CFR 61.156 ATP CTP curriculum includes at least 30 hours of classroom instruction and at least 10 hours of training in an FSTD, without issuing a type rating. An unrestricted multiengine ATP under 14 CFR 61.159 requires age 23, 1,500 hours total time, and at least 50 hours of flight time in the class of airplane. Up to 100 hours of that 1,500-hour total may be accomplished in an FFS or Flight Training Device (FTD) inside an approved Part 121, 135, 141, or 142 course. At most 25 hours in an FFS count toward the 50-hour multiengine class requirement, and FTD or Aviation Training Device (ATD) hours cannot be used.

Pause before self-funding a standalone jet rating. An ATP checkride in an FSTD is only permitted inside a Part 142 training center or an air carrier's approved training program. When a Part 121 or Part 135 operator hires you, 14 CFR 61.157 lets you earn your type rating inside the employer's curriculum while learning company Standard Operating Procedures (AC 120-71) and Crew Resource Management (AC 120-51). Paying for a standalone Part 142 rating mainly fits owner-pilots or contract Part 91 pilots with aircraft access, since air carriers retrain every new hire in-house.

Inside Training and the Type Rating Practical Test

A type rating syllabus progresses from systems ground school and cockpit procedure training to Full Flight Simulator (FFS) or aircraft evaluations. Core study texts listed in FAA-G-ACS-2 include the FAA-Approved Airplane Flight Manual (AFM), Quick Reference Handbook (QRH), Minimum Equipment List (MEL), Configuration Deviation List (CDL), type-specific Flight Standardization Board (FSB) Report, High-Altitude Operations guidance (AC 61-107), Stall Prevention and Recovery Training (AC 120-109), and Upset Prevention and Recovery Training (AC 120-111).

On checkride day, an FAA Aviation Safety Inspector, Designated Pilot Examiner, or Part 142 Training Center Evaluator tests your knowledge, risk management (checklist usage, distraction management, task prioritization, situational awareness, startle response, and undesired aircraft states), and flight skills across eight Areas of Operation in the ATP and Type Rating ACS. Once issued, a type rating never expires from your certificate, though exercising PIC privileges requires recurrent proficiency checks under 14 CFR 61.58 or Part 121/135 checking programs. Appendix 1 of the ACS also governs removing Second in Command Required, Circle-to-Land, or Supervised Operating Experience limitations.

  • Area I, Preflight Preparation: Systems, weight and balance, takeoff and landing performance speeds (V1, VR, V2, VREF), plus ATP weather, high-altitude aerodynamics, air carrier rules, human factors, and federal regulations.
  • Area II, Preflight Procedures: Flight deck inspection, powerplant start flows, runway incursion avoidance during taxi, and before-takeoff checks.
  • Area III, Takeoffs and Landings: Normal and crosswind takeoffs and landings, rejected takeoff actions at or prior to V1, and go-around or rejected landing maneuvers.
  • Area IV, In-Flight Maneuvers: Steep turns, unusual attitude recoveries, and type-specific flight characteristics.
  • Area V, Stall Prevention: Recognition and recovery at first stall indication in partial-flap, clean, and landing configurations.
  • Area VI, Instrument Procedures: Instrument takeoff, SIDs, STARs, precision, non-precision, and circling approaches, missed approaches, and holding.
  • Area VII, Emergency Operations: Memory items and QRH checklists, takeoff engine failure, inflight shutdown and restart, single-engine landing, manually flown single-engine precision approach, and no-flap or nonstandard-flap landing.
  • Area VIII, Postflight Procedures: After-landing flows, parking, shutdown, and securing.

FAA vs. EASA Type Ratings, Differences Training, and Rotorcraft Rules

Manufacturers design shared flight decks so crews can transition across model variants without repeating a full initial type rating, though the FAA and EASA divide several fleets differently. Under EASA Part-FCL and Commission Regulation (EU) No 748/2012, as amended by Regulation (EU) No 69/2014, variant differences training relies on Operational Suitability Data for flight crew. Under Part-21 rule 21.A.62, Type Certificate and STC holders must make that approved data available to end users. Multi-variant cells marked with an X on EASA's Aeroplanes Endorsement List share one license endorsement with required differences or familiarization training, such as Level B familiarization on certain Hawker 125 setups without an EFB package. By contrast, the FAA defines variant training requirements in aircraft FSB Reports.

On cross-border conversions, EASA's Aircrew Rulemaking and Standardization page notes that Member State National Competent Authorities (NCAs) issue individual licenses while EASA revises an Examiners Differences Document quarterly. Pilot Licensing Annex 3 of the EU-US Bilateral Aviation Safety Agreement (signed November 19, 2020) streamlines Private Pilot License (PPL) conversions only and excludes CPL and ATPL holders, who follow Commission Delegated Regulation (EU) 2020/723. Likewise, 14 CFR 61.71(b) limits foreign license credit toward FAA Part 61 certificates to applicable BASA terms.

Beyond fixed-wing airplanes, pilot certification and type ratings extend to rotorcraft, powered-lift under FAA-S-ACS-17 (effective May 31, 2024), and airships. EASA publishes separate Helicopter and Airship endorsement lists, designating the Zeppelin LZ N07-101 under LZ N07. In the United States, the FAA helicopter designation table assigns ratings such as AB-139/AW-139, AW189, SK-92, BV-234, S-70, and S-70M for the UH-60M, HH-60M, and HH-60W. That FAA table also places VFR Only limitations on helicopters lacking IFR certification.

Comparison of FAA Order 8900.1 Figure 5-88 and EASA Part-FCL airplane type rating designations

Aircraft Family FAA Type Rating Designation EASA License Endorsement Key Variant Coverage and Regulatory Distinction
Airbus A320 Single-Aisle Family A-320 A320 Covers A318, A319, A320, and A321 models (including neo and A321-200PCF under EASA with differences training)
Airbus A330 and A350 Widebodies A-330 and A-350 (separate) A330/350 (shared) FAA requires two distinct type ratings, while EASA groups A330 and A350-900/1000 under one endorsement with differences training
Boeing 737 Family B-737 B737 100-200 and B737 300-900 FAA groups 737-100 through 737-900ER and MAX 737-7, 737-8, and 737-9 under B-737, while EASA splits 100-200 from Classic, NG, and MAX
Boeing 757 and 767 B-757, B-767 B757/767 Shared common type rating across both FAA and EASA frameworks for 200, 300, 300F, and 767-400ER series
Boeing 777 and 787 Widebodies B-777 and B-787 (separate) B777/787 (shared) FAA separates B-777 and B-787, whereas EASA groups 777-200/300/F and 787-8/9/10 with differences training
Embraer E-Jets ERJ-170, ERJ-190 EMB170 Covers Embraer 170, 175, 190, and 195 series, including E190-E2 and E195-E2 (ERJ 190-300 and 190-400) variants
Cessna Citation CJ Series (525) CE-525 or CE-525S C525 FAA separates SIC Required (CE-525) from Single Pilot (CE-525S), while EASA lists C525 as Single-Pilot HPA with variant differences

Six-Step Type Rating Readiness Checklist Before Day 1

Simulator footprints move fast once ground school starts, leaving little margin for paperwork errors or unmemorized flows. Use this six-step preparation plan written by our team to arrive ready on Day 1.

  • Step 1, Match your IACRA, FTN, and knowledge test names: Under FAA-G-ACS-2, a last-name or suffix mismatch (such as Jr. or Sr.) between your Airman Knowledge Test Report (AKTR) and IACRA blocks electronic processing and forces a paper Form 8710-1, while first-name or middle-initial variations require an evaluator explanation and photo ID copy. Verify your FAA Tracking Number (FTN) and legal name in IACRA before booking with PSI.
  • Step 2, Secure your AKTR and ATP CTP certificate: For a concurrent multiengine ATP and type rating, bring your ATP CTP graduation certificate and unexpired AKTR. Duplicate AKTRs for tests taken on or after January 13, 2020 can be printed via PSI (tests on or before January 10, 2020 follow 14 CFR 61.29).
  • Step 3, Check Block 2 and the FSB Report: For Part 91 or Part 135 business aircraft, match Block 2 of the Airworthiness Certificate to the FAA designation table and confirm whether you are testing for a Single Pilot code (such as CE-525S) or an SIC Required code.
  • Step 4, Lock down QRH memory items and AFM limitations: Memorize boxed emergency recall actions and hard AFM system limits before Day 1 so simulator sessions focus on flying rather than hunting checklists.
  • Step 5, Rehearse Pilot Flying and Pilot Monitoring callouts: Chair-fly V1 cuts, manually flown single-engine precision approaches, and stall recoveries out loud to meet Crew Resource Management (AC 120-51) and SOP monitoring (AC 120-71) standards.
  • Step 6, Pack your Practical Test Checklist folder: Assemble a government photo and signature ID showing a physical residential address, pilot and medical certificates, endorsed logbooks, graduation certificate, and IACRA or paper Form 8710-1 at least 48 hours ahead.

Practice example

Tell me about how you plan to prepare for the pace of your first transport-category jet type rating and simulator evaluation.

Example answer, written by us. It is not a real applicant's story. When I completed my multiengine ATP Certification Training Program, those 10 hours in the Flight Simulation Training Device showed me how quickly high-altitude jets compress workload compared to light piston twins. Before Day 1 of airline ground school, my plan is to lock down every boxed Quick Reference Handbook memory item and Airplane Flight Manual limitation cold so I never spend mental bandwidth searching for recall items in the box. During systems and procedures training, I chair-fly normal flows, V1 engine-failure profiles, and single-engine precision approaches out loud with a study partner, practicing both Pilot Flying and Pilot Monitoring standard callouts. That way, when we step into the Full Flight Simulator for the ATP-standard checkride, my scan is already ahead of the airplane and I can focus on threat management, checklist discipline, and clear crew communication.

This answer shows the panel you understand the difference between the ATP CTP course and a full type rating checkride, and it names concrete study habits grounded in QRH memory items, AFM limitations, and Pilot Monitoring callouts rather than generic promises to study hard.

Practice this on Fourstripe. Pick your airline and a captain runs the interview out loud: TMAAT, about-you, technical and scenario questions, with real follow-ups. You get a scored report on every answer. 7-day trial, then from $149 a week. Start a practice interview

Frequently asked questions

What is a type rating in aviation?

A type rating is an official certification added to a pilot certificate or license authorizing you to operate a specific aircraft make, model, or variant family, such as an Airbus A-320 or Boeing B-737, beyond standard single-engine or multiengine class privileges. Under FAA Order 8900.1 and Commission Regulation (EU) No 1178/2011 (FCL.700), earning one requires model-specific ground and flight or simulator training plus an ATP-standard practical test.

When do you need a type rating and how does the 12,500-pound rule apply?

Under 14 CFR 61.31 and the FAA type designation tables, you need a type rating to act as pilot on aircraft certificated or operated above 12,500 pounds maximum takeoff weight, any turbojet-powered airplane regardless of weight, and designated helicopters or multi-pilot aircraft. Under 14 CFR 121.436, both Captains and First Officers in Part 121 air carrier operations must also hold a full type rating for the aircraft flown.

Does an SIC type rating under 14 CFR 61.55 count for Part 121 airlines?

No. Under 14 CFR 121.436(b), a Second-in-Command pilot type rating obtained under 14 CFR 61.55 does not satisfy Part 121 airline First Officer requirements, and 14 CFR 61.55(e) was amended to remove Part 121 issuance.

What is the difference between the ATP CTP course and a type rating?

Under 14 CFR 61.156, the ATP Certification Training Program (ATP CTP) is a prerequisite course of at least 30 classroom hours and at least 10 Flight Simulation Training Device hours required before taking the multiengine ATP knowledge test. It prepares pilots for transport-category operations without issuing a type rating, whereas a type rating trains and tests you on a specific aircraft model under FAA-S-ACS-11A.

Do the Boeing 737 MAX and Airbus A320neo require separate type ratings?

No, both the FAA airplane designation table and the EASA Aeroplanes Endorsement List group the Boeing 737 NG and MAX together (under FAA B-737 and EASA B737 300-900) and group the Airbus A320ceo and A320neo families together (under FAA A-320 and EASA A320). Pilots already rated on the base type qualify on the newer variant through approved differences training rather than a separate type rating.

Can I convert an FAA type rating to EASA through the EU-US BASA?

Not under the fast-track PPL annex. Pilot Licensing Annex 3 of the EU-US Bilateral Aviation Safety Agreement (signed November 19, 2020) applies strictly to Private Pilot Licenses and excludes Commercial and Airline Transport Pilot Licenses, which follow standard EU conversion rules under Delegated Regulation (EU) 2020/723.

Sources