Transport Category V-Speeds (V1, VR, V2) and Part 25 Takeoff Performance

Short answer: Under 14 CFR 1.2 and Part 25 (up to date as of November 9, 2026), V1 is the maximum speed where you must initiate the first stopping action to stay within accelerate-stop distance. It is also the minimum speed after an engine failure at VEF to continue the takeoff within takeoff distance. VR is the rotation speed where the nose gear is raised. Under 14 CFR 25.111, V2 is the takeoff safety speed reached before 35 feet above the takeoff surface, guaranteeing the required climb gradient on one engine.

Core Part 25 Takeoff Speeds in Order of the Takeoff Roll

Airline technical panels test whether you understand the difference between general aviation operating speeds and transport category airworthiness standards under 14 CFR Part 25. In transport category airplanes, takeoff speeds are dynamic values calculated for each departure based on gross weight, field elevation, ambient temperature, runway slope, wind, and surface contamination under 14 CFR 25.105.

When explaining the takeoff sequence during a technical screening, present the speeds in their exact operational order from brake release to initial climb, citing their governing Part 1 or Part 25 criteria.

  • VMCG (Ground Minimum Control Speed): The lowest calibrated airspeed during the takeoff run at which directional control can be maintained using primary aerodynamic controls alone when the critical engine suddenly becomes inoperative, as established under 14 CFR 25.107(a)(1) and 25.149(e).
  • VEF (Engine Failure Speed): Defined in 14 CFR 1.2 and 25.107(a)(1) as the calibrated airspeed at which the critical engine is assumed to fail during takeoff. Selected by the applicant, VEF cannot be less than VMCG.
  • V1 (Takeoff Action Speed): Defined in 14 CFR 1.2 as the maximum speed in takeoff where the pilot must take the first action (such as applying wheel brakes, reducing thrust, or deploying speed brakes) to stop the airplane within the accelerate-stop distance. It is also the minimum speed following critical engine failure at VEF to continue takeoff and reach the required height above the takeoff surface within the takeoff distance.
  • VR (Rotation Speed): Defined in 14 CFR 1.2 and 25.107(e) as the speed where the pilot initiates raising the nose gear off the runway. Under 14 CFR 25.107(e)(1), VR cannot be less than V1.
  • VMU (Minimum Unstick Speed): Defined in 14 CFR 25.107(d) as the calibrated airspeed at and above which the airplane can safely lift off the ground and continue takeoff.
  • VLOF (Lift-Off Speed): Defined in 14 CFR 25.107(f) as the calibrated airspeed at which the airplane first becomes airborne. Landing gear retraction may not begin until the airplane is airborne under 14 CFR 25.111(b).
  • V2MIN (Minimum Takeoff Safety Speed): Defined in 14 CFR 25.107(b) as not less than 1.10 times VMC and not less than 1.13 VSR for two-engine and three-engine turboprops and turbojets without provisions for significant reduction in one-engine-inoperative stall speed, or 1.08 VSR for airplanes with those provisions or more than three propeller engines.
  • V2 (Takeoff Safety Speed): Defined in 14 CFR 1.2 and 25.107(c). V2 is the takeoff safety speed reached before 35 feet above the takeoff surface, guaranteeing the required one-engine-inoperative climb gradient. Under 14 CFR 25.111(c)(2), you must attain V2 before reaching 35 feet above the takeoff surface and maintain a speed as close as practical to, and not less than, V2 until 400 feet above the takeoff surface.
  • VFTO (Final Takeoff Speed): Defined in 14 CFR 1.2 and 25.107(g) as the speed achieved at the end of the takeoff path when configuration cleanup is complete. VFTO cannot be less than 1.18 VSR.

Part 25 Takeoff Speed Certification Floors (14 CFR 25.107 and 25.111)

Speed 14 CFR Section Regulatory Lower Limit Operational Function
VEF 25.107(a)(1) At least VMCG Assumed failure point of critical engine
V1 1.2, 25.107(a)(2) At least VEF plus speed gained during recognition and reaction First physical stopping action initiated by this speed
VR 25.107(e)(1) At least V1 Pilot begins pitch rotation to liftoff attitude
VLOF 25.107(f) Selected above VMU Airframe leaves the runway surface
V2MIN 25.107(b) At least 1.13 VSR (or 1.08 VSR) and at least 1.10 VMC Aerodynamic certification floor for V2
V2 25.107(c), 25.111(c)(2) At least V2MIN and VR plus speed increment before 35 feet Attained before 35 feet, guarantees climb gradient
VFTO 25.107(g) At least 1.18 VSR Final takeoff climb speed in en route configuration

VEF and V1: Why V1 Is an Action Speed Rather Than a Decision Speed

A common technical interview trap is referring to V1 as the speed where you decide whether to abort. FAA Advisory Circular 25-7C states that V1 is intended to be at the end of the decision process and includes the time it takes for the pilot to perform the first action to stop the airplane.

Under 14 CFR 25.107(a)(2), V1 cannot be less than VEF plus the speed gained with the critical engine inoperative during the time interval between engine failure and the instant the pilot recognizes and reacts by initiating the first stopping action, such as applying wheel brakes, reducing thrust, or deploying speed brakes.

When an interviewer asks how to handle an engine failure occurring exactly at V1, the regulatory answer is clear: you must continue the takeoff. Under 14 CFR 1.2 and 25.107(a)(2), stopping within the accelerate-stop distance requires that the first physical stopping action be taken at V1. A failure occurring at V1 will not be recognized until the aircraft has accelerated past V1, exceeding the maximum speed to reject within certified stopping margins.

Under 14 CFR 25.109(a)(1)(iv) and (a)(2)(iii), an additional distance equivalent to 2 seconds at V1 is incorporated into dry runway accelerate-stop calculations. As outlined in AC 25-7C paragraph 11, because transport airplanes require multiple pilot inputs (such as brakes, throttles, and ground spoilers) to achieve maximum braking configuration, this 2-second buffer accounts for operational delays in activating secondary deceleration devices rather than additional decision time.

Rotation Speed (VR) and Takeoff Safety Speed (V2) Certification Rules

Under 14 CFR 25.107(e)(2), a single value of VR must be scheduled for a given weight, configuration, and ambient condition to demonstrate compliance with both one-engine-inoperative and all-engines-operating takeoff standards. Pilots do not alter their target rotation speed based on whether an engine has failed.

To protect against operational variations on the line, 14 CFR 25.107(e) and AC 25-7C establish strict flight test handling limits:

  • Service variations and mistrim: Under 14 CFR 25.107(e)(4) and AC 25-7C, operational variations and unannunciated mistrim must not cause unsafe flight characteristics. AC 25-7C defines a marked increase in takeoff distance as any amount exceeding 1 percent of scheduled field length.
  • Weight effect on VMCA: AC 25-7C paragraph 23 explains that because 14 CFR 25.149(b) allows up to 5 degrees of bank into the operating engine when determining VMCA, the lateral component of weight helps balance sideslip and rudder forces. Heavier weights produce a lower VMCA, making minimum control speeds most limiting at light gross weights.

Accelerate-Stop Distance, Reverse Thrust, and Wet Runway Rules

Under 14 CFR 25.109, certified accelerate-stop distance evaluates two distinct rejected takeoff profiles and mandates publishing the greater distance. On a dry runway under 14 CFR 25.109(a), accelerate-stop distance is the greater of the engine-failure rejected takeoff distance or the all-engines-operating rejected takeoff distance, both including an additional 2-second distance buffer at V1.

Regulatory friction criteria and decelerating means differ significantly between dry and wet surfaces:

  • Reverse thrust credit: Under 14 CFR 25.109(f)(1), reverse thrust cannot be included as an additional means of deceleration on dry runways. On wet runways, 14 CFR 25.109(f)(2) permits reverse thrust credit if it is safe, reliable, consistent, and requires no exceptional piloting skill.
  • Wet runway anti-skid efficiency: Under 14 CFR 25.109(c)(2), unless flight test analysis provides a specific efficiency, the tire-to-ground wet braking friction coefficient is adjusted by default values: 0.30 for On-Off systems, 0.50 for Quasi-Modulating systems, and 0.80 for Fully Modulating systems.
  • Grooved and porous friction runways: Under 14 CFR 25.109(d)(1), operators may define the wet runway braking coefficient as 70 percent of the dry runway braking coefficient on grooved or porous friction course surfaces.
  • Brake wear test standard: Under 14 CFR 25.109(i), flight demonstrations of maximum brake kinetic energy accelerate-stop distance must be conducted with no more than 10 percent of the allowable brake wear range remaining.

Takeoff Distance, Takeoff Run, Clearways, and Stopways

Under 14 CFR 25.113(a), dry runway takeoff distance is the greater of two values: the one-engine-inoperative distance from takeoff start to 35 feet above the takeoff surface, or 115 percent of the all-engines-operating distance to 35 feet. On a wet runway under 14 CFR 25.113(b), takeoff distance is the greater of the dry runway takeoff distance or the distance to 15 feet above the surface achieved while reaching V2 before 35 feet.

Balanced Field Length is the condition where the accelerate-stop distance equals the accelerate-go distance to screen height following an engine failure at VEF. When a runway has no clearway or stopway, selecting a balanced V1 produces the shortest required runway length for a given aircraft weight. Introducing a clearway extends takeoff distance and permits a lower V1, while adding a stopway extends accelerate-stop distance and permits a higher V1. In both cases, the available field becomes unbalanced.

  • Clearway definition: AC 25-7C paragraph 13 states that a clearway is an upward sloping plane extending from the end of the runway with a slope not exceeding 1.25 percent, above which no terrain or obstacle protrudes. The clearway is treated as an extension of the runway surface for measuring distance to screen height.
  • Takeoff Run versus Takeoff Distance (14 CFR 25.113(c)): When no clearway is used, takeoff run equals takeoff distance. When a clearway is used on a dry runway, takeoff run is the greater of the horizontal distance to the midpoint between VLOF and 35 feet above the surface (OEI), or 115 percent of the all-engine distance to that same midpoint.
  • Wet Runway Takeoff Run with Clearway (14 CFR 25.113(c)(2)): On a wet runway with a clearway, takeoff run is the greater of the horizontal distance to 15 feet above the takeoff surface, or 115 percent of the all-engine distance to the midpoint between VLOF and 35 feet.
  • Stopway corrections: Under 14 CFR 25.109(h), stopways are credited exclusively in accelerate-stop calculations. If the stopway surface differs substantially from the runway, operational correction factors must account for the surface characteristics and seasonal weather variations.

Worked Example: Calculating 2-Second V1 Margin and All-Engine Factor

Here is how to apply Part 25 distance margins in a calculation question.

First, consider the 2-second V1 distance margin required under 14 CFR 25.109(a)(1)(iv). If an aircraft has a dry runway V1 of 140 knots true ground speed, converting knots to feet per second (140 multiplied by 1.6878 feet per second per knot) equals 236.3 feet per second. By our calculation from 14 CFR 25.109(a)(1)(iv), traveling for 2 seconds at this speed adds 472.6 feet to the certified accelerate-stop distance beyond the physical braking run.

Second, consider the 115 percent all-engines-operating factor under 14 CFR 25.113(a)(2). If an aircraft requires 5,400 feet to reach 35 feet with an engine failure at VEF, and requires 4,800 feet with all engines operating, the all-engine distance must be multiplied by 1.15. By our calculation from 14 CFR 25.113(a)(2), 115 percent of 4,800 feet equals 5,520 feet. Because 5,520 feet exceeds the 5,400-foot engine-out distance, the certified dry takeoff distance is 5,520 feet.

Takeoff Path Segments, Climb Gradients, and Environmental Corrections

Under 14 CFR 25.111(a), the takeoff path extends from a standing start to 1,500 feet above the takeoff surface or to the point where en route transition is complete and VFTO is reached, whichever is higher.

The following operational restrictions and climb limits apply during initial departure:

  • Restrictions below 400 feet AGL (14 CFR 25.111(c)(4)): Aircraft configuration may not be altered, except for gear retraction and automatic propeller feathering, and no pilot action to reduce thrust or power may be initiated below 400 feet above the takeoff surface.
  • Climb gradient floors at 400 feet AGL (14 CFR 25.111(c)(3)): The airborne flight path must remain positive at each point. Beginning at 400 feet above the takeoff surface, available climb gradients must not be less than 1.2 percent for two-engine airplanes, 1.5 percent for three-engine airplanes, and 1.7 percent for four-engine airplanes.

15 Part 25 Takeoff Performance Questions to Practice Out Loud

Use this study checklist to rehearse your technical delivery. Practice verbalizing each answer cleanly in under 60 seconds using official regulatory references.

    1. How does 14 CFR 1.2 define V1, and why does the definition contain two parts?
    1. What is VEF under 14 CFR 25.107(a)(1), and how does it relate to VMCG and V1?
    1. Why does AC 25-7C specify that V1 is an action speed rather than a decision speed?
    1. What operational factors does the 2-second V1 distance margin in 14 CFR 25.109(a) accommodate?
    1. Why does 14 CFR 25.109(a) require testing an all-engines-operating rejected takeoff?
    1. Can reverse thrust credit be used to reduce dry runway accelerate-stop distance under 14 CFR 25.109(f)?
    1. What brake wear condition is required during maximum kinetic energy tests under 14 CFR 25.109(i)?
    1. What regulatory constraints govern VR under 14 CFR 25.107(e)?
    1. How is V2MIN calculated under 14 CFR 25.107(b), and by what height must V2 be attained under 14 CFR 25.111(c)(2)?
    1. How does the required screen height change from a dry runway to a wet runway under 14 CFR 25.113?
    1. Why does 14 CFR 25.113(a)(2) apply a 115 percent factor to the all-engines takeoff distance?
    1. What distinguishes Takeoff Distance from Takeoff Run when a clearway is present under 14 CFR 25.113(c)?
    1. What is Balanced Field Length, and how do clearways and stopways create an unbalanced field?
    1. What control and thrust changes are prohibited before reaching 400 feet AGL under 14 CFR 25.111(c)(4)?
    1. What climb gradient floors are required at 400 feet AGL under 14 CFR 25.111(c)(3)?

How to Structure Your Verbal Answers in the Technical Panel

When an interviewer asks you a performance question, structure your answer into three simple steps. First, state the plain definition. Second, give the governing regulation or certification target. Third, explain how you apply it in the cockpit.

Practice your delivery out loud so your words come out smoothly and naturally. You want to sound like a knowledgeable colleague discussing airplane certification, not someone reciting a study guide.

Practice example

Walk me through the exact relationship between VEF and V1, and tell me whether you would stop or continue if an engine failed right at V1.

Example answer, written by us. It is not a real applicant's story. Under 14 CFR Part 1 and Part 25.107, VEF is the calibrated airspeed at which the critical engine is assumed to fail during the takeoff roll, and it cannot be less than VMCG. V1 is established from VEF by adding the speed gained with the critical engine inoperative during the time it takes the pilot to recognize and react to the failure by taking the first action to stop the airplane. Because 14 CFR 1.2 defines V1 as the maximum speed at which the pilot must take the first stopping action to remain within the accelerate-stop distance, V1 is at the end of the decision process, not the start of it. If an engine fails right at V1, by the time I recognize the failure and react, the airplane will already be above V1. Therefore, if the failure happens at V1, I would continue the takeoff, rotate at VR, and climb out at V2 before 35 feet above the takeoff surface.

This answer directly distinguishes VEF from V1 using 14 CFR 1.2 and 25.107(a), explains that V1 marks the initiation of the first physical stopping action, and resolves the classic engine-failure-at-V1 scenario without hesitation.

Practice this on Fourstripe. Pick your airline and a captain runs the interview out loud: TMAAT, about-you, technical and scenario questions, with real follow-ups. You get a scored report on every answer. 7-day trial, then from $149 a week. Start a practice interview

Frequently asked questions

What is the exact FAA Part 1 definition of V1?

Under 14 CFR 1.2, V1 is the maximum speed in takeoff at which the pilot must take the first action (such as applying brakes, reducing thrust, or deploying speed brakes) to stop the airplane within the accelerate-stop distance. It also means the minimum speed following critical engine failure at VEF to continue takeoff and achieve the required height above the takeoff surface within the takeoff distance.

By what altitude must V2 be reached and how long must it be maintained?

Under 14 CFR 25.111(c)(2), the airplane must attain V2 before reaching 35 feet above the takeoff surface. It must then continue at a speed as close as practical to, and not less than, V2 until reaching 400 feet above the takeoff surface.

Is thrust reverser credit permitted in Part 25 dry runway accelerate-stop calculations?

No. Under 14 CFR 25.109(f)(1), the effects of available reverse thrust shall not be included as an additional means of deceleration when determining accelerate-stop distance on a dry runway. Reverse thrust credit may be approved on wet runways under 14 CFR 25.109(f)(2) if it meets reliability, consistency, and pilot skill standards.

What is the difference between dry and wet runway takeoff screen heights?

Under 14 CFR 25.113(a), dry runway takeoff distance is measured to 35 feet above the takeoff surface. Under 14 CFR 25.113(b), wet runway takeoff distance may be measured to 15 feet above the takeoff surface, provided the aircraft achieves V2 before reaching 35 feet above the takeoff surface.

What are the regulatory constraints on rotation speed (VR)?

Under 14 CFR 25.107(e)(1), VR cannot be less than V1, must permit reaching V2 before 35 feet above the takeoff surface, and must provide adequate margin above minimum unstick speed (VMU) to ensure safe lift-off.

What is a clearway and how does it affect takeoff run under Part 25?

AC 25-7C defines a clearway as a plane extending from the runway end with an upward slope not exceeding 1.25 percent, above which no object or terrain protrudes. Under 14 CFR 25.113(c), when a clearway is used on a dry runway, takeoff run is measured to the midpoint between VLOF and the 35-foot height point rather than the full distance to 35 feet.

Sources