What is FADEC? Jet Engine Control Explained

Short answer: Full Authority Digital Engine Control (FADEC) is an autonomous electronic control system with full-range authority over an aircraft engine's power or thrust from idle to 100 percent maximum rated output. There is no manual control mode or direct mechanical link for the pilot to override the computer, so if the entire FADEC system fails, the engine fails. To match the safety of traditional hydromechanical controls under FAA Advisory Circular 33.28-1 (issued June 29, 2001), transport-category electronic engine controls use dual-channel redundancy and dedicated power sources to keep Loss of Thrust Control (LOTC) events to no more than 1 per 100,000 engine operating hours.

What Full Authority Means in the Cockpit

FAA Advisory Circular 33.28-1 defines Electronic Engine Control (EEC) as the broader family of electrical and electronic engine controls, which includes supervisory controls and Full Authority Digital Engine Control (FADEC). In a supervisory system, a computer fine-tunes engine parameters, but the system can revert to a hydromechanical control if the electronics fail. FADEC removes pilot-operated manual reversion entirely.

According to the FAA Safety Briefing fact sheet on FADEC (updated February 4, 2022), full authority means the pilot has no direct mechanical control over the engine. Moving the thrust lever turns a throttle position transducer that sends an electrical request signal to the digital computer. The computer evaluates engine and environmental sensors hundreds of times per second and positions the actuators to deliver the requested thrust.

First introduced in turbine aircraft, FADEC is now widely used in spark-ignition and compression-ignition (jet-fuel diesel) piston aircraft as well.

In a piston aircraft, FADEC eliminates magnetos, carburetor heat, mixture controls, and engine priming. It combines throttle, propeller, and mixture levers into a single power lever with detents such as start, idle, cruise power, and max power. During startup, the computer primes the cylinders and adjusts the mixture based on engine temperature and ambient pressure. In cruise, it adjusts fuel flow and ignition timing for each individual cylinder.

  • Autonomous operation: The system manages start sequencing, idle speed, and power modulation without manual leaning or propeller governing.
  • Self-monitoring diagnostics: Sensors track powerplant health and trigger cockpit service lights when small problems appear.
  • Full-range authority: The computer governs 100 percent of the operating envelope, including fuel flow, stator vanes, bleed valves, and operating limits.
  • Redundant architecture: Dual digital channels and independent backup electrical power prevent a single component fault from shutting down the engine.

FADEC Architecture and Sensor Voting Logic

The complete FADEC system includes the digital electronic unit, wiring harnesses, dedicated sensors, and the mechanical, pneumatic, or hydromechanical actuators that meter fuel and airflow. Basic mechanical components that do not interface with the electronic controller, such as the main fuel pump, are not considered part of the FADEC system.

In early turbine EEC certifications documented in AC 33.28-1 Appendix 1, manufacturers built dual-channel redundancy from the sensed inputs to dual output devices for the three critical control loops: fuel, stator vanes, and bleed control. As detailed in Chapter 7 of the FAA Pilot's Handbook of Aeronautical Knowledge (PHAK), turbine engines experience compressor stalls when the angle of attack on the compressor blades becomes too high, causing airflow to stagnate or reverse. FADEC prevents compressor stalls and rich or lean flameouts by scheduling fuel metering alongside variable inlet guide vanes and stator vanes that direct incoming air into the rotor blades at the proper angle.

To calculate thrust schedules, the engine control computer relies on local engine sensors (measuring rotor speeds N1 and N2, exhaust gas temperature, turbine inlet temperature, and pressures) and aircraft-supplied data from the airframe's Air Data Computers (ADCs). Title 14 of the Code of Federal Regulations (14 CFR) section 33.28(b) requires that any failure of aircraft-supplied data must not cause an unacceptable change in power or thrust, or prevent continued safe engine operation.

To comply with 14 CFR 33.28(b), FADEC systems use fault accommodation logic built around sensor voting. The computer compares dual sources of aircraft-supplied data against local engine sensors that act as voters. If one ADC sends corrupted data, the local engine voter sensors identify the mismatch and eliminate the erroneous source. If all aircraft-supplied ADC inputs fail simultaneously, the FADEC switches to its local engine sensors as the primary data source. If those local engine sensors also fail, the software falls back on mathematically modeled or synthesized engine parameters to keep the engine running.

Dual-Channel Redundancy and Loss of Thrust Control (LOTC)

Because electronic components can fail randomly without the gradual wear that inspections catch on hydromechanical units, 14 CFR 33.28(c) mandates that no single electrical or electronic failure can result in an unsafe condition. FADEC systems prevent loss of thrust by incorporating two separate and identical digital channels. Each channel can provide all engine and propeller functions without operational limitations if the other channel fails.

Certificated FADEC architectures use either two identical electronic channels or a single electronic channel paired with a simplified electronic or hydromechanical backup mode. If an active electronic channel suffers an unaccommodated fault, the system automatically transfers control to the healthy channel or alternate mode. Automatic mode transfers are generally limited to thrust changes of less than about 10 percent.

The FAA evaluates FADEC reliability by measuring the probability of a Loss of Thrust Control (LOTC) event, or a Loss of Power Control (LOPC) event in reciprocating engines under AC 33.28-2 (dated 08/13/03). For transport airplanes (Part 25), commuter airplanes (Part 23), and rotorcraft (Parts 27 and 29), an LOTC is the loss of ability to modulate and maintain thrust between flight idle and 90 percent of maximum rated thrust. For normal, utility, and acrobatic Part 23 airplanes, the threshold is 85 percent of rated power, matching the historical 15 percent maximum power loss caused by losing one magneto in a dual-magneto piston engine.

Because 2 to 5 percent of potential electronic faults in a dual-channel system may be uncovered (meaning they cannot be practically detected or accommodated), the FAA considers these systems essentially single-fault tolerant. Under Time-Limited Dispatch (TLD) policies and Time-Limited Operations (TLO) in AC 33.28-2, operators can fly with minor degraded faults present for a strict window, such as 20 hours for degraded reciprocating systems, provided the instantaneous failure rate stays within certified limits. By our calculation from Table 5-1 and Table 5-2 in AC 33.28-2, the maximum allowable LOPC rate for a reciprocating engine EEC with three or more subsystems increases by a factor of 10 when operating in a 20-hour TLO degraded state compared to a full-up system (rising from 45 events per million hours to 450 events per million hours).

FAA Electronic Engine Control Reliability Standards (AC 33.28-1 and AC 33.28-2)

Aircraft Category Failure Metric Definition Maximum Allowable Rate Primary Architecture
Part 25 Transport Airplanes & Parts 27/29 Turbine Rotorcraft LOTC: Inability to modulate thrust between flight idle and 90% rated thrust 1 event per 100,000 engine flight hours (10 per million hours) Dual identical digital channels, or single channel with full hydromechanical backup
Part 23 Normal, Utility, & Acrobatic Airplanes (General) LOTC: Inability to modulate power between flight idle and 85% rated power 40,000 hours Dual electronic channels or single channel with simplified alternate mode
Part 23 Reciprocating Engines (Full-Up System, 3+ Subsystems) LOPC: Inability to attain at least 85% rated power or modulate power 45 LOPC events and 450 Minor Power Loss (85% to 95% power) events per million hours Redundant electronic fuel, ignition, and turbocharger wastegate subsystems
Part 23 Reciprocating Engines (Degraded TLO State, 20-Hour Limit) LOPC: Operating with a detected fault that reduces redundancy 450 LOPC events and 4,500 Minor Power Loss events per million hours Single remaining healthy channel or degraded sensor configuration

Electrical Power Supply and Dedicated Engine Alternators

Sufficient electrical power is required both to start and to run a FADEC engine, which means hand-propping a dead piston aircraft will not work. To prevent an airframe electrical emergency from shutting down the engines in flight, 14 CFR 33.28(b) requires that a complete failure or interruption of aircraft-supplied electrical power must not cause an unacceptable change in thrust or prevent safe engine operation.

On transport category jets and many turbine aircraft, manufacturers comply with 14 CFR 33.28(b) by mounting a dedicated alternator or generator directly on the engine. As described in AC 33.28-1 Chapter 5 and AC 33.28-2 Chapter 4, this self-contained engine power source is physically and functionally isolated from the main aircraft electrical bus. Even if an alternator has dual windings, a dedicated winding routed exclusively to the FADEC counts as a self-contained engine power source.

This dedicated engine alternator is the primary power supply for the FADEC once the engine is running, sized with enough margin to power the computer across temperature and idle speed variations, including in-flight restarts. If the dedicated engine-mounted alternator fails, the FADEC automatically draws backup power from the aircraft's main electrical bus or battery.

Certain engine functions that have historically relied on airframe electricity are excepted from the dedicated engine power requirement: non-critical functions, engine start, ignition, thrust reverser, anti-icing, and fuel shut-off. In aircraft where the engine control is integrated with the avionics and uses aircraft-supplied power as primary power, a dedicated backup battery must be installed. That backup battery must be isolated from the starting battery and hold enough charge to allow a safe landing from the aircraft's maximum certificated altitude after losing all generators and alternators, including at least one missed approach and go-around.

How FADEC Prevents Overspeed and Overtemp

In a traditional mechanically linked engine, pushing the levers full forward in an emergency can overboost the cylinders, exceed turbine inlet temperature limits, or overspeed the rotors. With FADEC, you cannot exceed engine limits by advancing the thrust levers. The system's range of control spans from idle to 100 percent maximum rated thrust and actively enforces engine temperature, torque, pressure, and red-line rotor speed limits. When a pilot commands maximum power, the FADEC delivers the maximum allowable power for that flight level and no more.

To prevent an uncontained rotor burst caused by a control malfunction or a shaft failure, FAA compliance guidance sets strict rules for electronic overspeed protection. First, the overspeed protection system must be independent from normal FADEC control. If the normal control channel and the overspeed protection system share any resources, the probability of a shared fault causing an overspeed while inhibiting the protection function must be less than 1 event per billion engine flight hours (10^-9).

Second, the combined engine and overspeed protection system must be at least two independent faults removed from a rotor burst when one fault induces the overspeed. The probability of an uncontrolled overspeed combined with an overspeed protection failure must be 1 event per 100 million engine flight hours (10^-8), or less than 10^-9 in some aircraft installations, while the failure rate of the overspeed protection system itself must be on the order of 1 event per 10,000 hours (10^-4).

Because a dormant failure in the overspeed circuit would leave the engine one fault away from a rotor burst, an electronic overspeed protection system must undergo a self-test before every flight. Verification at engine shutdown of the previous run is acceptable. When multiple electronic paths can invoke the overspeed system, the FADEC tests a different path each engine cycle. The control system cannot be knowingly dispatched if the overspeed protection system is inoperative or has a failure rate greater than 10^-4 per hour.

  • Step 1 (Pilot Input): You advance the thrust lever to the maximum power detent, sending a request signal via the throttle position transducer.
  • Step 2 (Parameter Scheduling): The active FADEC channel reads air data and local engine sensors (N1, N2, EGT/TIT, pressure) to compute the fuel flow and stator vane schedule.
  • Step 3 (Limit Governing): As rotor speed or turbine temperature approaches red-line limits, the normal control loop modulates fuel so the engine produces 100 percent rated thrust for that flight level without crossing temperature, torque, pressure, or speed limits.
  • Step 4 (Independent Overspeed Guard): If a primary control fault drives rotor RPM past red line, the independent overspeed protection circuit overrides normal control and actuates the fuel shut-off mechanism.
  • Step 5 (Post-Flight Verification): During engine shutdown, the FADEC automatically self-tests an electronic overspeed protection path to verify availability for the next flight.

How to Explain FADEC in Your Airline Pilot Interview

When an airline interview panel asks you to explain FADEC, structure your explanation around four pillars from FAA certification standards: full authority without manual reversion, dual-channel redundancy, electrical independence, and automatic limit protection. Use the checklist below to deliver a complete answer in under 90 seconds.

  • Define Full Authority: State that there is no mechanical linkage to the engine and no manual reversion mode. The computer has 100 percent authority from idle to max rated thrust.
  • Explain Dual-Channel Redundancy: Mention that each engine has two separate, identical digital channels, and either channel can run all engine functions without limitations if the other fails.
  • Describe Electrical Independence: Explain that once running, the FADEC is powered by a dedicated engine-mounted alternator, with the aircraft main electrical bus serving as backup.
  • Highlight Limit Protection: Note that FADEC enforces red-line speed, temperature, torque, and pressure limits automatically when you push the thrust levers full forward, backed by an independent overspeed protection circuit that self-tests at shutdown.

Environmental, Lightning, and Software Certification Standards

Under 14 CFR 33.28(d), electronic hardware must undergo at least 10 temperature variation cycles alongside vibration and explosion-proof testing under RTCA Document DO-160D. Systems are also tested against High Intensity Radiated Fields (HIRF) at 200 volts per meter average from 10 kHz to 18 GHz. During multiple-stroke and multiple-burst lightning bench tests, large-engine cable shields carry 1,000 to 2,000 amperes. Across these HIRF and lightning tests, the FADEC must meet a 'no effect' pass criterion. That means any power or thrust change stays within plus or minus 2 percent of normal governing capability for less than 1 second, with no channel transfers, false fault announcements, or component damage.

Within the takeoff envelope (at or below 1,500 feet AGL for airplanes or 1,000 feet AGL for Category A rotorcraft), an uncovered control fault or undetected aircraft signal fault causing more than a 3 percent thrust loss is generally unacceptable for Part 25 transport jets. Outside the takeoff envelope at high altitude and high airspeed, undetected aircraft signal faults are limited to thrust changes of less than about 15 percent.

Under 14 CFR 33.28(e), FADEC software on Part 25 engines must be designed to RTCA DO-178B Level A (or DO-178A Level 1), while programmed logic devices like Application Specific Integrated Circuits (ASICs) and Field Programmable Gate Arrays (FPGAs) follow RTCA DO-254. If a nacelle fire occurs in a fire zone, the FADEC and its fire-resistant fuel shut-off valve (under 14 CFR 33.17 and 33.75) must allow a safe engine shutdown without hazardous actions.

Practice example

What is FADEC, how is it powered on a transport-category jet, and how does it prevent you from overboosting or overtemping the engine during a windshear escape?

Example answer, written by us. It is not a real applicant's story. FADEC stands for Full Authority Digital Engine Control. Full authority means the digital computer controls the engine from idle to 100 percent rated thrust, with no mechanical linkage or manual reversion mode for the pilot. Because a total FADEC failure would shut down the engine, the system uses two separate and identical digital channels, Channel A and Channel B. Each channel can run all engine functions without limitations if the other fails. Under 14 CFR 33.28, the FADEC is isolated from airframe electrical failures by drawing primary power from a dedicated engine-mounted alternator, while the main aircraft electrical bus serves as backup. During a windshear escape, I can push the thrust levers full forward to the stop without exceeding engine limits. The thrust lever transducer sends a request for maximum thrust, and the FADEC schedules fuel flow, variable stator vanes, and bleed valves to deliver maximum rated thrust for that altitude and temperature without exceeding EGT, pressure, or red-line rotor speed limits. An independent overspeed protection circuit also guards against a rotor burst and self-tests during engine shutdown.

This answer covers the core FAA certification requirements in logical order. It defines 'full authority' accurately (no manual reversion), explains dual-channel redundancy, identifies the dedicated engine alternator as primary power with aircraft bus backup, and explains both normal parameter limiting and the independent overspeed circuit.

Practice this on Fourstripe. Pick your airline and a captain runs the interview out loud: TMAAT, about-you, technical and scenario questions, with real follow-ups. You get a scored report on every answer. 7-day trial, then from $149 a week. Start a practice interview

Frequently asked questions

What does 'Full Authority' mean in a FADEC system?

Full authority means the electronic control unit has complete control over engine power or thrust from idle to 100 percent rated output, with no direct pilot mechanical linkage and no manual control mode. If the entire FADEC system and its backups fail, the engine stops operating.

How is a FADEC powered if the aircraft loses all electrical generators?

Under 14 CFR 33.28(b), a failure of aircraft-supplied electrical power cannot prevent continued safe engine operation. Most turbine FADEC systems draw primary power from a dedicated, self-contained alternator mounted directly on the engine, using the aircraft's main electrical bus only as a backup power source.

What happens if one channel of a dual-channel FADEC fails in flight?

Nothing changes for engine performance. Dual-channel FADEC systems incorporate two separate and identical digital channels, and each channel is capable of providing all engine functions without operational limitations if the other channel fails.

Can a pilot push a FADEC engine past its temperature or speed limits in an emergency?

No. Automatic engine performance monitoring provides continuous overspeed and overboost protection across the entire operating range, so commanding full throttle delivers the maximum allowable power for that altitude and no more.

How does FADEC test its overspeed protection system?

Electronic overspeed protection systems must be independent of normal control and undergo a functional self-test before each flight. Manufacturers typically satisfy this requirement by programming the FADEC to run an automatic verification test during the engine shutdown sequence of the previous flight.

What happens if the Air Data Computers feeding the FADEC fail?

Under fault accommodation rules, local engine sensors act as 'voters' to reject corrupted data from an Air Data Computer. If all aircraft-supplied air data is lost, the FADEC reverts to its local engine sensors as the primary source, and if those fail, it uses mathematically synthesized parameters to keep the engine operating safely.

Sources