Wake Turbulence Rules and Avoidance for Pilots

Short answer: Short answer: Wake turbulence is a pair of counter-rotating cylindrical vortices generated from the moment an aircraft rotates on takeoff until it touches down on landing, reaching peak strength when the aircraft is heavy, clean, and slow. Per FAA AIM Section 7-4 and AC 90-23G (replaced by AC 90-23H on January 13, 2026), vortices sink at several hundred feet per minute and move laterally outward at 2 to 3 knots within 100 to 200 feet of the ground. To avoid an induced roll, fly at or above a larger aircraft's approach path and land beyond its touchdown point, or rotate prior to its rotation point on departure.

Last checked November 4, 2026.

How Wake Vortices Form and When They Are Strongest

Every aircraft in flight generates wake turbulence as a by-product of lift. According to AIM Section 7-4-2 and AC 90-23G, lift comes from a pressure differential over the wing surfaces, with the lowest pressure over the upper wing and the highest pressure under the wing. This triggers the airflow to roll up aft of the wing into two counter-rotating cylindrical vortices trailing from the wingtips in cruise, and nominally from the outboard edge of the outboard flap on approach and landing. Most of the energy is concentrated within a few feet of the center core, where peak speeds up to almost 300 feet per second have been recorded.

When viewed from ahead or behind, vortex circulation flows outward, upward, and around the wingtips. Winglets improve cruise fuel efficiency by reducing induced drag, but FAA studies show they have a negligible effect on wake generation during slower departure and arrival speeds. Vortex strength is governed by weight, speed, wingspan, and wing shape, increasing proportionately with higher operating weight or lower airspeed. Because mechanical turbulence from a dirty configuration (extended flaps and gear) hastens wake decay, the greatest vortex strength occurs when the generating aircraft is heavy, clean, and slow. You will regularly hear this in pilot technical interview questions, where examiners check that you connect high weight and low speed with a clean wing.

The primary hazard of a wake encounter is an induced rolling moment that exceeds your aircraft's roll-control authority. Flight testing shows your ability to counter an imposed roll depends primarily on your wingspan and control responsiveness. When your wingspan and ailerons extend beyond the rotational flow field of the vortex, counter-control is usually effective. Short-wingspan aircraft relative to the generating aircraft, even high-performance jets, have a much harder time countering the roll.

  • Wake begins and ends with lift: An aircraft generates trailing vortices from the exact moment it rotates on takeoff until it touches down on landing.
  • High-altitude cruise factor: Reduced air density at high altitude can produce wake strength comparable to the terminal area, and higher closure speeds leave less time for the wake to decay.

Vortex Behavior: Sink Rate, Ground Effect, and Wind Drift

At altitudes greater than one wingspan above the ground, the two vortices remain spaced slightly less than a wingspan apart and drift with the wind. Vortices from larger aircraft sink at several hundred feet per minute, slowing their descent and losing strength over time and distance. In stable en route conditions with light winds, low atmospheric turbulence, and low stratification, vortices from Heavy and Super aircraft can descend more than 1,000 feet. Conversely, ambient thermal lifting, rising terrain or tree lines (orographic effects), wind shear tilting, or bouncing off a strong inversion layer can cause a vortex flow field to rise.

When vortices from a large aircraft sink within 100 to 200 feet of the ground, they move laterally outward over the ground at 2 to 3 knots, at an altitude slightly less than one-half the wingspan. How surface wind interacts with that 2-to-3-knot movement is a common topic in pilot interview weather questions.

  • No wind: Both vortices sink to within 100 to 200 feet of the surface and move outward away from the runway centerline at 2 to 3 knots.
  • Light crosswind (1 to 5 knots): Decreases the lateral movement of the upwind vortex and increases the movement of the downwind vortex, holding the upwind vortex in the touchdown zone while hastening the downwind vortex toward an adjacent runway.
  • Light quartering tailwind (maximum caution): Pushes the preceding aircraft's vortices forward into the final approach and touchdown zone while the crosswind component holds the upwind vortex over the centerline.

Pilot Avoidance Procedures by Phase of Flight

Whether or not Air Traffic Control issues a CAUTION - WAKE TURBULENCE advisory, you are expected to adjust your flight path to prevent an encounter. Because vortices trail behind and sink below the generating aircraft, stay at or above the larger aircraft's flight path and upwind of its track.

On visual approaches, the FAA recommends that Super, Heavy, and Large jet operators fly on the established glidepath, never above it, or follow a 3-to-1 glidepath profile (3,000 feet at 10 miles from touchdown, 1,500 feet at 5 miles, 1,200 feet at 4 miles). If you are flying a lighter trailing aircraft with the lead aircraft and runway in sight, fly on or slightly above the glidepath and pick a landing point no less than 1,000 feet from the arrival threshold. Maintain a line-of-sight to that point above and ahead of the lead aircraft, and land beyond its touchdown point. For example, aim for the 1,500-foot markings if tire smoke appears at the 1,000-foot markings (about 500 feet beyond), while verifying adequate stopping distance.

Because vortices from a Heavy aircraft at 1,500 feet at 5 miles from touchdown sink at several hundred feet per minute, sagging below the 3-to-1 glidepath inside 4 miles (1,200 feet) places your wings directly into the descending vortex path.

  • Landing behind a larger aircraft (same runway or parallel runway closer than 2,500 feet): Stay at or above the larger aircraft's final approach path, note its touchdown point, and land beyond it (watching for drift from close parallel runways).
  • Landing behind a larger aircraft (crossing runway): Cross above the larger aircraft's flight path.
  • Landing behind a departing larger aircraft (same runway): Note the rotation point and land well prior to it.
  • Landing behind a departing larger aircraft (crossing runway): If it rotates past the intersection, continue and land prior to the intersection. If it rotates prior to the intersection, avoid flight below its path and abandon the approach unless landing is assured well before the intersection.
  • Departing behind a larger aircraft (full length or intersection): Note the rotation point, rotate prior to that point, climb above its climb path until turning clear, and avoid headings that cross below and behind it.
  • After a low approach, missed approach, or touch-and-go: Wait at least 2 minutes before takeoff or landing (at least 3 minutes behind a Super aircraft).
  • En route VFR (thousand-foot altitude plus 500 feet): Avoid flight below and behind a large aircraft's path and adjust laterally upwind.
  • Helicopters: Avoid operating within three rotor diameters of a helicopter in a stationary hover or slow hover taxi. In forward flight, helicopters produce strong trailing vortices similar to a large fixed-wing airplane.

Pilot Responsibility, Visual Approaches, and Upset Recovery

Controllers apply mandatory wake separation to IFR aircraft, VFR aircraft receiving Class B, Class C, or TRSA services, and VFR aircraft being radar sequenced. However, accepting specific ATC clearances transfers wake separation responsibility directly to you. Under 14 CFR 91.3(a), the pilot-in-command is final authority as to the operation of the aircraft. When in doubt on approach, ask the tower for separation distance and groundspeed updates. Request any extra departure separation (such as 2 minutes instead of 4 or 5 miles) on ground control before taxiing onto the runway.

  • Three situations where the pilot accepts wake separation responsibility: (1) Accepting traffic information, (2) Accepting instructions to follow an aircraft, and (3) Accepting a visual approach clearance.
  • In-flight vortex encounter recovery: Wake upsets can involve rapid roll reversals. Avoid abrupt reversals of aileron and rudder. Using rudder to counter roll rate can cause an undesirable response, and large control reversals can exceed structural design limits.
  • Transitioning the wake and autopilot use: If altitude permits, it may be better to let the aircraft transition through the wake and recover from the resulting unusual attitude rather than fighting the roll in the core. If the autopilot stays engaged, it may be better to let the autopilot recover while staying ready to take manual control if it disconnects.
  • Reporting: Notify ATC of any wake encounter (bank angle, altitude deviation, intensity, duration) and file an Aviation Safety Reporting System (ASRS) report.

Traditional Weight Classes and FAA Radar Separation Standards

Under the legacy system, aircraft are grouped by maximum certificated takeoff weight (MTOW): Super (Airbus A380, Antonov AN-225), Heavy (300,000 pounds or greater), Large (more than 41,000 pounds up to 300,000 pounds, with special rules for the Boeing B757), and Small (41,000 pounds or less). Super and Heavy pilots must state Super or Heavy in terminal radio calls.

Radar separation applies directly behind a Super or Heavy at the same altitude or less than 1,000 feet below, and to Small aircraft directly behind a B757 at the same altitude or less than 500 feet below. Online AIM 7-4-9 and AIP 7-4-9 / AC 90-23G Table 1 differ slightly on three pairs: AIM lists Heavy behind Super at 5 miles (AIP/AC list 6 miles), Heavy behind Heavy at 3 miles (AIP/AC list 4 miles), and Small behind B757 at 4 miles in-trail (AC Table 1 lists 5 miles at the threshold).

  • Same-threshold, close parallel (<2,500 ft with <500 ft stagger), or crossing departure intervals: 3 minutes behind a Super, 2 minutes behind a Heavy, and 2 minutes for a Small behind a B757 (non-waivable).
  • Intersection or opposite-direction departure behind a Large (non-B757): 3 minutes for a Small aircraft. This is the only legacy wake interval that may be waived upon specific pilot request.
  • Intersection or opposite-direction departure behind a B757, Heavy, or Super: 3 minutes for a Small behind a B757, 3 minutes for any aircraft behind a Heavy, and 4 minutes for any aircraft behind a Super on the same or parallel runway less than 2,500 feet apart (controllers may not reduce or waive these intervals).
Lead Aircraft Trailing Aircraft Directly Behind Radar Minima (AIM / AIP) At Landing Threshold (AC 90-23G / AIM) Full-Length / Crossing Departure Interval Intersection / Opposite-Direction Interval
Super Heavy 5 NM (AIM) / 6 NM (AIP) 6 NM 3 min 4 min
Super B757 / Large 7 NM 7 NM 3 min 4 min
Super Small 8 NM 8 NM 3 min 4 min
Heavy Heavy 3 NM (AIM) / 4 NM (AIP) 4 NM 2 min 3 min
Heavy B757 / Large 5 NM 5 NM 2 min 3 min
Heavy Small 5 NM 6 NM 2 min 3 min
B757 Heavy / B757 / Large MRS 4 NM (AC 90-23G) Standard MRS Standard
B757 Small 4 NM (AIM) 5 NM (AC 90-23G) 2 min 3 min
Large (non-B757) Small MRS 4 NM Standard 3 min (waivable by pilot)

Wake Turbulence Recategorization (RECAT) and CWT Categories

Under FAA Order JO 7110.659C (effective 02/29/16) and AC 90-23G Appendix 2, Wake Turbulence Recategorization (RECAT) replaces weight-only classes with six aircraft wake categories (Categories A through F) based on maximum takeoff weight (MTOW), wingspan, approach speed, and ability to counteract adverse roll. Under RECAT (JO 7110.659C), visual separation is not authorized when the lead aircraft is a Category A (Super). By our calculation from Table 1 and JO 7110.659C Table 5-5-1, RECAT reduces directly-behind radar spacing for a B747 (Category B) behind another B747 from 4 NM to 3 NM (a 25 percent reduction), while increasing approach spacing for a Category F aircraft behind a Category B aircraft from 6 NM to 7 NM within 5 NM of the final approach fix.

In current FAA Order JO 7110.65BB Chapter 3 Section 9 (Consolidated Wake Turbulence), wake categories are expanded to nine categories (Categories A through I). Same-runway departure separation is 3 minutes for Category B through I aircraft behind a Category A aircraft, and 2 minutes behind Categories B, D, C, or E depending on the follower category. Specifically, the 2-minute rule applies to Category B through I behind Category B or D, Category E through I behind Category C, and Category I behind Category E on the same runway or a parallel runway separated by less than 700 feet. Intersection departures require 4 minutes behind Category A and 3 minutes behind Categories B, C, D, E, F, G, or H depending on the follower category.

In the table below, the two slash-separated numbers show Directly Behind / On Approach Within 5 NM of FAF (for example, 5 NM / 7 NM means 5 NM directly behind and 7 NM on approach), and MRS means Minimum Radar Separation.

  • Category A: MTOW of 300,000 pounds or more and wingspan greater than 245 feet (A380, AN-225).
  • Category B: MTOW of 300,000 pounds or more and wingspan greater than 175 feet and less than or equal to 245 feet (B747, B777, B787, A330, A340).
  • Category C: MTOW of 300,000 pounds or more and wingspan greater than 125 feet and less than or equal to 175 feet (B767, MD11, A306, DC10).
  • Category D: MTOW less than 300,000 pounds and wingspan greater than 125 feet and less than or equal to 175 feet, or MTOW greater than 41,000 pounds with wingspan greater than 90 feet and less than or equal to 125 feet (B757, B737, A320, E190).
  • Category E: MTOW greater than 41,000 pounds with wingspan greater than 65 feet and less than or equal to 90 feet (CRJ1/2/7/9, E170, E135/145, AT72).
  • Category F: MTOW less than 41,000 pounds and wingspan less than or equal to 125 feet, or MTOW less than 15,500 pounds regardless of wingspan, or a powered sailplane (C650, C525, B190, general aviation single and multi-engine aircraft).
Leader / Follower Cat A Cat B Cat C Cat D Cat E Cat F
Category A MRS 5 NM / 5 NM 6 NM / 6 NM 7 NM / 7 NM 7 NM / 7 NM 8 NM / 8 NM
Category B MRS 3 NM / 3 NM 4 NM / 4 NM 5 NM / 5 NM 5 NM / 5 NM 5 NM / 7 NM
Category C MRS MRS MRS 3.5 NM / 3.5 NM 3.5 NM / 3.5 NM 5 NM / 6 NM
Category D MRS MRS MRS MRS MRS 4 NM / 4 NM
Category E & F MRS MRS MRS MRS MRS MRS

Checklist and Scenario Follow-Ups for Your Pilot Interview

In airline pilot interview questions and pilot scenario interview questions, panels test your cockpit decision habit pattern. Use this five-step checklist written by our team, followed by two scenario follow-ups to practice.

Scenario 1: Cleared for a visual approach behind a Heavy or B757 with a 3-knot quartering tailwind while drifting below the glideslope. State three facts: accepting the visual approach transferred legal wake separation responsibility to you, the quartering wind holds the preceding vortex in the touchdown zone, and sagging below the glidepath puts you in the sinking core. If you cannot immediately regain a path at or above the glideslope and land beyond the lead's touchdown point with safe stopping distance, execute a go-around and request radar vectors.

Scenario 2: Tower asks if you can take an immediate intersection departure behind a B757, Heavy, or regional jet. State that under JO 7110.65BB 3-9-7 and the AIM, intersection intervals behind a Super (4 minutes), Heavy (3 minutes), or B757 (3 minutes for a Small) cannot be waived by either pilot or controller. Even for a Small aircraft behind a non-B757 Large (or a Category I aircraft behind a departing Category F, G, or H aircraft under CWT) where the 3-minute interval is waivable upon specific pilot request, explain that under 14 CFR 91.3(a) you would hold for the full 3 minutes if winds could drift the wake across your takeoff roll.

    1. Check the 1-to-5-knot wind trap: Break tower wind into crosswind and tailwind components to see if the upwind vortex will linger in the touchdown or rotation zone.
    1. Audit your clearance: Accepting traffic info, instructions to follow, or a visual approach makes wake spacing your responsibility. Decline the visual or ask for vectors if you cannot stay at or above the lead's path.
    1. Mark rotation or touchdown points: Rotate prior to a larger aircraft's rotation point and climb above its path, or land at least 500 feet beyond its tire smoke if stopping distance permits.
    1. Request extra departure time early: Behind a Super (3 minutes full-length or 4 minutes from an intersection), Heavy, B757, or low/missed approach (2 to 3 minutes), request any extra time on ground control before crossing the hold-short line.
    1. Brief the go-around and upset plan: Go around if a crossing departure rotates prior to your intersection, and avoid abrupt aileron or rudder reversals if you encounter wake.

Practice question

Walk me through how wake turbulence is generated, what makes it strongest, how surface winds affect it, and how you avoid it on approach and departure.

Example answer, written by us. It is not a real applicant's story. Wake turbulence is a by-product of lift. High pressure under the wing rolls up toward the low pressure over the upper wing, creating two counter-rotating cylindrical vortices that start at rotation on takeoff and end at touchdown. Vortex strength is governed by weight, speed, wingspan, and wing configuration, so wake is strongest when the generating aircraft is heavy, clean, and slow. Vortices sink at several hundred feet per minute and level off or descend over 1,000 feet en route behind a Heavy or Super. Once they sink within 100 to 200 feet of the ground, they move laterally outward at 2 to 3 knots, so a 1 to 5 knot crosswind or a light quartering tailwind can keep a vortex in the touchdown zone. To avoid it on departure behind a larger airplane, I note its rotation point, rotate prior to that point, and climb above its flight path. On landing, I stay at or above its glidepath, note its touchdown point, and land beyond it.

This answer hits every FAA keyword from AIM 7-4 and AC 90-23: pressure differential, rotation to touchdown, heavy-clean-slow, sink rate, the 2-to-3-knot ground effect spread, the 1-to-5-knot crosswind and quartering tailwind hazard, and exact takeoff and landing flight path adjustments.

Practice this on Fourstripe. A panel captain asks TMAAT, about-you, technical and scenario questions out loud, follows up on what you said, and scores every answer. 7-day trial, then from $149 a week. Start a practice interview

Fourstripe is not affiliated with any airline.

Frequently asked questions

When is aircraft wake turbulence the strongest?

The greatest vortex strength occurs when the generating aircraft is heavy, clean (flaps and landing gear retracted), and slow. Vortex strength increases proportionately with higher operating weight and slower airspeed, while a clean wing lacks the flap turbulence that hastens wake decay.

Why does a light quartering tailwind require maximum caution for wake turbulence?

A 1 to 5 knot crosswind component counteracts the 2-to-3-knot outward movement of the upwind vortex while the tailwind component pushes the vortices forward into the final approach and touchdown zone.

Do winglets reduce wake turbulence on approach and departure?

No. While winglets improve fuel efficiency by reducing induced drag during cruise, studies show they have a negligible effect on wake turbulence generation at the slower speeds flown during departures, approaches, and landings.

When is a pilot responsible for their own wake turbulence separation?

A pilot accepts responsibility for wake turbulence avoidance and safe takeoff or landing intervals when operating VFR outside controlled separation services, or when accepting traffic information, instructions to follow another aircraft, or a visual approach clearance from ATC.

Can a pilot waive the 2-minute or 3-minute wake turbulence takeoff delay?

Neither pilots nor controllers may waive wake turbulence departure intervals behind a Super, Heavy, or B757 (or Categories A through E under JO 7110.65BB). A pilot may only initiate a request to waive the 3-minute interval when departing as a Small aircraft from an intersection or opposite direction behind a standard non-B757 Large aircraft (or as a Category I aircraft behind a Category F, G, or H aircraft for an intersection takeoff, or behind a Category F or G aircraft for an opposite-direction takeoff).

What is RECAT and did AC 90-23H replace AC 90-23G?

Wake Turbulence Recategorization (RECAT) replaced the legacy four weight classes with six categories (A through F in JO 7110.659C) and later nine Consolidated Wake Turbulence categories (A through I in JO 7110.65BB) based on MTOW, wingspan, approach speed, and roll moment capability. Additionally, the FAA canceled AC 90-23G and replaced it with AC 90-23H, Aircraft Wake Vortex Encounter Risk Mitigation.

Sources

Related guides